Subscribe to Our Youtube Channel
Related Manuals for MAGIC FX ECO2JET BRACKET
Summary of Contents for MAGIC FX ECO2JET BRACKET
- Page 1 USER AND INSTALLATION MANUAL ENGLISH ECO2JET ® BRACKET. PART00000 ACCESSORIES rev 01-00...
-
Page 2: Disclaimer
LIABILITY MAGIC FX accepts no liability for claims from third parties arising from unauthorised use, use other than that stated in this manual, and use other than in accordance with the General Conditions registered at the Chamber of Commerce. -
Page 3: Table Of Contents
Safety General safety rules Indoor/outdoor use Rigging Noise Levels Safety symbols Safety precautions Installation and use Mount the ECO2JET BRACKET to the ECO2JET Mount a clamp Clamp it to a truss Maintenance Troubleshooting Correct disposal EC Declaration of Conformity MAGICFX ECO2JET —... -
Page 4: Introduction
ECO2JET BRACKET. Authorised personnel are those who: • Are appointed by their supervisor to install and/or operate ECO2JET with the ECO2JET BRACKET at the event. • Are trained in recognizing and avoiding hazards related to SFX applications at events. -
Page 5: Language
LANGUAGE This document contains the original instructions in English. In case you require other languages please contact MAGIC FX. ABBREVIATIONS Abbreviation Description ECO2JET MAGICFX ECO2JET ® ECO2JET BRACKET MAGICFX ECO2JET BRACKET ® Abbreviations REVISION TABLE Doc nr Revision Date Description... -
Page 6: Meet The Magicfx ® Eco2Jet Bracket
® The ECO2JET BRACKET is an accesory that is designed for the ECO2JET. With the ECO2JET BRACKET it is possible to hang the ECO2JET below a truss in different angles / positions. The ECO2JET BRACKET is only meant for use in combination with the ECO2JET. Use in combination with other machines is not permitted. -
Page 7: Technical Data
TECHNICAL DATA Product Product Name ECO2JET BRACKET Product Code Product Type ACCESSORIES Main Length Dimensions Width Height Weight Weight Work Load Limit Environment Minimum Temperature °C °F Maximum Temperature °C °F Humidity (Relative) 20 % to 90 % (non condensing) -
Page 8: Safety
SAFETY The ECO2JET BRACKET has been designed and constructed in such a manner that it can be used safely. This applies to the use, the circumstances and the regulations as described in this documentation. Reading this documentation and following the instructions are therefore necessary for everyone who is authorised to work with this accessory. -
Page 9: Noise Levels
MAGICFX is not responsible for any rigging equipment and WARNING accessories provided by third party manufacturers. Verify that the Work Load Limit (WLL) of all additional hardware rigging accessories is respected. NOISE LEVELS The measured maximum noise level of the product is 95 dB(A) at 1 m distance. This level of noise is only reached during the short instances that the output is active. -
Page 10: Installation And Use
When the ECO2JET will be used under a certain angle it is highly recommended to use the ECO2JET BRACKET. Mount the ECO2JET BRACKET to the ECO2JET using the supplied fasteners and fix the ECO2JET BRACKET to a truss using the proposed truss clamps. -
Page 11: Mount A Clamp
Adjust the fixing points and move the loose bracket to acquire the desired angle of the ECO2JET. MOUNT A CLAMP Mount a clamp (MFX3104 or MFX3106) to the ECO2JET BRACKET (MFX1804) using the provided bolts and nuts. MAGICFX ECO2JET — User and Installation Manual... -
Page 12: Clamp It To A Truss
CLAMP IT TO A TRUSS Mount the ECO2JET BRACKET witht the ECO2JET in horizontal position onto a horizontal truss. CAUTION Take the recoil of the ECO2JET into account. Make sure the construction is prepared for the counter force of firing the effect. - Page 13 Secure the ECO2JET onto the truss with use of the safety eye. Make sure the safety cable is as short as possible. If needed, wind the cable around the truss to pull it tight. By default, the machine is programmed to autoflip the display. However, to preserve a particular configuration use “flip mode”...
-
Page 14: Maintenance
MAINTENANCE To achieve the maximum service life of the ECO2JET BRACKET you must regularly clean the ECO2JET BRACKET and test if it is functioning correctly. Contact MAGIC FX if the ECO2JET BRACKET is not functioning correctly. Do not replace parts yourself; always consult MAGIC FX. -
Page 15: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY MAGICFX ECO2JET — User and Installation Manual ®... - Page 16 WWW.MAGICFX.EU...
Need help?
Do you have a question about the ECO2JET BRACKET and is the answer not in the manual?
Questions and answers