4 channel controller for 100-250vac on/off special effects machines (14 pages)
Summary of Contents for MAGIC FX CO2 GUN II
Page 1
USER AND INSTALLATION MANUAL ENGLISH CO2 GUN II ® PART01169 CO2 FX REV 01-03...
Page 2
LIABILITY MAGIC FX accepts no liability for claims from third parties arising from unauthorised use, use other than that stated in this manual, and use other than in accordance with the General Conditions registered at the Chamber of Commerce.
2.3. Indoor Use 2.4. Noise Levels 2.5. Safety symbols 2.6. Safety warnings Installation and use 3.1. Connect CO2 3.2. Blast 3.3. Clean up Troubleshooting Maintenance Correct disposal EC Declaration of Conformity MAGICFX CO2 GUN II® — User and installation manual...
INTRODUCTION Congratulations! You have bought a great new product from MAGIC FX. This manual contains all information required for the intended use of the equipment. Deviation from the described intended use can result in a hazardous situation and/or property damage.
DESCRIPTION The CO2 GUN II is a handheld gun-shaped device for safe shooting of CO2 into the air. Before operation the CO2 GUN II needs to be connected to a CO2 cylinder. When the user squeezes the handle, the CO2 is released from the barrel. The shot is accompanied by a strong hissing sound and a white plume of smoke will be visible from the barrel.
14 °F Maximum Temperature 70 °C 158 °F Humidity (Relative) 20 to 90 % (non-condensing) IEC 60529 (IP) Rating IP12 Controlling Control Options Manual Technical data 1.3. PRODUCT IDENTIFICATION Type plate MAGICFX CO2 GUN II® — User and installation manual...
Please contact MAGIC FX for additional possibilities. SAFETY The CO2 GUN II has been designed and constructed in such a manner that it can be used safely. This applies to the use, the circumstances and the regulations as described in this documentation. Reading this documentation and following the instructions are therefore necessary for everyone who is authorised to work with the CO2 GUN II.
2.3. INDOOR USE The CO2 GUN II is designed for outdoor use and use in well-ventilated indoor spaces. When used indoors, make sure you take the necessary preparations. These preparations could include, but are not limited to: •...
2.5.. During operation electrostatic discharge can occur NOTICE when the machine is touched. Prevent the discomfort of a possible static shock by wearing gloves. MAGICFX CO2 GUN II® — User and installation manual...
INSTALLATION AND USE 3.1. CONNECT CO2 Make sure that the safety catch is in locking position. Connect the CO2 hose to the CO2 quick connector. MAGICFX CO2 GUN II® — User and installation manual...
Page 11
Connect a CO2 bottle-to-hose connector to a CO2 cylinder. Connect the CO2 hose to the CO2 bottle-to-hose connector on the CO2 cylinder. MAGICFX CO2 GUN II® — User and installation manual...
Open the CO2 cylinder. 3.2. BLAST Carefully walk to the desired shooting position. Unlock the safety catch. MAGICFX CO2 GUN II® — User and installation manual...
Page 13
Firmly hold with two hands and aim above the audience. Make sure that the direct output is free from persons, animals and objects. When it’s time to shoot, squeeze the handle. Enjoy the view! Release the handle to stop shooting. MAGICFX CO2 GUN II® — User and installation manual...
Place the safety catch back in locking position. 3.3. CLEAN UP Close the CO2 cylinder. MAGICFX CO2 GUN II® — User and installation manual...
Page 15
Unlock the safety catch. Squeeze the handle to release the remaining pressure. MAGICFX CO2 GUN II® — User and installation manual...
Page 16
Place the safety catch back in locking position. Disconnect the CO2 hose from the CO2 quick connector. MAGICFX CO2 GUN II® — User and installation manual...
Page 17
Disconnect the CO2 hose from the CO2 bottle-to-hose connector on the CO2 cylinder. Remove the CO2 bottle-to-hose connector from the cylinder. Store the gun. MAGICFX CO2 GUN II® — User and installation manual...
MAINTENANCE To achieve the maximum service life of the CO2 GUN II you must regularly clean the CO2 GUN II and test if it is functioning correctly. Contact MAGIC FX if the CO2 GUN II is not functioning correctly.
According to Annex III A Machinery Directive 2006/42/EC Serial number : on product The following harmonized standards were applied: MAGIC FX B.V. declares as manufacturer and composer of the technical construction file that the Year of construction : on product product with the following specifications:...