Banana Pi BPI-M1 Manual page 80

How to build OpenWRT image from github
[ 7.313783] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 7.324800] procd: - early -
[ 7.327825] procd: - watchdog -
[ 8.196631] procd: - ubus -
[ 9.200629] procd: - init -
[ 9.740779] NET: Registered protocol family 10
[ 9.750621] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.781222] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 9.789242] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 9.797957] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.808055] nf_conntrack version 0.5.0 (16024 buckets, 64096 max)
[ 9.895305] xt_time: kernel timezone is -0000
[ 9.909554] cfg80211: Calling CRDA to update world regulatory domain
[ 9.916314] cfg80211: World regulatory domain updated:
[ 9.921471] cfg80211: DFS Master region: unset
[ 9.926943] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.936834] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.944963] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.952992] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.961171] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.969328] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.978922] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.987125] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.995867] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.033695] PPP generic driver version 2.4.2
[ 10.039216] NET: Registered protocol family 24
[ 10.057795] rtl8192cu: Chip version 0x11
[ 10.148074] rtl8192cu: MAC address: ac:a2:13:5c:96:bf
[ 10.153232] rtl8192cu: Board Type 0
[ 10.164227] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 10.170284] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 10.177753] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 10.179863] usbcore: registered new interface driver rtl8192cu
[ 11.862773] random: nonblocking pool is initialized
[ 14.869421] b53_common: found switch: BCM53125, rev 4
[ 14.899568] RX IPC Checksum Offload disabled
[ 14.916057] No MAC Management Counters available
[ 14.921020] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.864711] stmmaceth 1c50000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 16.872809] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 220.810635] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 221.264426] rtl8192cu: MAC auto ON okay!
[ 221.301871] rtl8192cu: Tx queue select: 0x05
[ 221.725855] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 221.734477] device wlan0 entered promiscuous mode
[ 221.739510] br-lan: port 1(wlan0) entered forwarding state
[ 221.745096] br-lan: port 1(wlan0) entered forwarding state
[ 221.752455] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 221.772506] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 223.741765] br-lan: port 1(wlan0) entered forwarding state
80