Extron electronics IN1808 Series Setup Manual page 6

Command
Video Mute
Mute output video
Mute video on all outputs
Mute video and sync
Unmute video and sync
View output mute status
Audio Configuration
Set audio input format
View audio input format
Front Panel Lockout (Executive Modes)
Enable lock mode 1
Enable lock mode 2
Enable lock mode 3
Enable lock mode 4
Disable executive modes
IP Settings
Set scaler IP address
Set scaler DHCP mode
Set subnet mask
Set gateway IP address
Reboot network
NOTE: IP settings do not take effect until the
Twisted Pair Protocol
Set input TP type
View input TP type
Set output TP type
View output TP type
DTP Remote Power Parameters
Set input remote power
View input remote power
Set output 1B remote power
View output 1B remote power
KEY:
X!
= Input selection
X@
= Output selection
X1)
= Enable or disable
X6^
= DTP remote power
X4@
= Video mute status
X5*
= Audio input type
X6&
= TP format
X8&
= IP address
X8*
= Subnet mask
X8(
= Gateway address
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide
© 2019 Extron Electronics — All rights re
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
6
ASCII Command
X@
*1B
1B
2B
0B
B
}
E X! X5*
I * AFMT
}
E I X! AFMT
1X
2X
3X
4X
0X
E X8& }
CI
E X( }
DH
E X8* }
CS
E X8( CG }
E }
2BOOT
E }
2BOOT
E X! X6& }
I * HDBT
E X! }
I HDBT
E O 2* X6& HDBT }
E }
O 2 HDBT
E X! X6^ }
I * RPWR
E I X! RPWR }
E X6^ }
O 2* RPWR
E O X@ RPWR }
Inputs 1 through 8. For the Twisted Pair Protocol commands,
1 = Output 1A (HDMI/DVI), 2 = Output 1B / 2 DTP/XTP/HDBT, 3 = Loop Output – HDMI/DVI
0 = off or disabled, 1 = on or enabled)
0 = Off (No remote power, default), 1 = DTP 12 VDC, 2 = DTP2 48 VDC
0 = unmuted, 1 = muted
0 = None (input muted), 1 = Analog aux line (5-pole captive screw), 2 = LPCM-2Ch digital, 3 = Multi-Ch digital,
4 = LPCM-2Ch digital audio aux line (default), 5 = Multi-Ch digital auto aux line.
0 = DTP format (default), 1 = XTP, 2 = HDBaseT format (supported on output only)
nnn.nnn.nnn.nnn), 192.168.254.254 = default
nnn.nnn.nnn.nnn), 255.255.255.0 = default
nnn.nnn.nnn.nnn), 0.0.0.0 = default
on the Extron website.
www.extron.com
served.
Response Additional Description
X4@ ]
Vmt *1 Mute the video on output
Mute the video on all outputs.
Vmt1 ]
] Mute the video and sync on all outputs.
Vmt2
Unmute the video on all outputs.
]
Vmt0
Vmt X4@ •X4@ •X4@ ] View mute status
1 2 3
(3).
]
X! X5* Set the audio format of input
AfmtI *
]
View the audio format of input
X5*
Lock all front panel controls.
]
Exe1
] Lock the front panel except for input selection, logo
Exe2
configuration, and volume adjustment.
Lock the front panel except for input selection and logos.
Exe3 ]
] Lock the front panel except for volume adjustment.
Exe4
Allow all front panel adjustments and selections.
]
Exe0
• X8&] Specifies a new scaler IP address.
Ipi
X(]
Idh Enables or disables DHCP (0 = default).
• X8*] Specifies a new subnet mask.
Ips
Specifies a new gateway IP address.
Ipg • X8(]
] Restarts the network connection after IP or DHCP
Boot2
changes.
command is executed.
X! X6&]
HdbtI * Set the DTP/XTP type for input
X6&]
View the current DTP/XTP type for input
Hdbt O 2* X6&]
Set the TP type for input
X6&]
View the DTP/XTP/HDBT setting
RpwrIX!*X6^]
Set remote power on input
X6^] View remote power setting on input
RpwrO 2*X6^] Set remote power on output 1B to
View remote power setting on output .
X6^]
X!
= Inputs 7 and 8 only.
All trademarks mentioned are the property of their respective owners.
X@
.
X4@ for outputs 1A (1), 1B (2), and loop
X! X5*
to .
X!
.
X! X6&
to .
X!
.
X! X6&
to .
X6&
on output 1B.
X! X6^
to .
X! .
X6^
.
68-3131-51 Rev. A
02 19