Advertisement
IN1808 Series Configuration
To configure IN1808 Series, use the front panel controls, the
on-screen display (OSD) menu, internal web pages, PCS, or SIS
commands.
On-screen Display (OSD) Menu System
To configure IN1808 Series using the OSD menu, connect a display
to either HDMI output 1A or to a DTP/XTP matrix switcher/HDBaseT
compatible device. The OSD menu consists of eight submenus accessed
using the front panel Menu or Enter button (see the example at right).
Extron Product Configuration Software
To configure IN1808 scalers using PCS, install the software (available on
the Extron website, www.extron.com) to a PC connected to the scaler
via Ethernet or front panel USB Config port. After the installation, start the
program. For full instructions, press <F1> on the keyboard or click the ?
button in the software and select Help File.
Internal Web Pages
To configure the IN1808 Series using the factory-installed web pages in a web browser (see the example at right), connect the
AV LAN connector (IPCP models) or LAN connector (base model) on the IN1808 to a LAN or WAN. The default IP address is
192.168.254.254.
Basic SIS Command Table
To configure IN1808 Series with specific SIS commands via an RS-232, USB, or Ethernet connection, use the Extron DataViewer
utility or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of
SIS commands and variables, see the IN1806 and IN1808 Series User Guide at www.extron.com.
Command
Input Selection
Select audio and video input
Select video input only
Select audio input only
Auto-Image
Execute Auto-Image™
Execute Auto-Image and fill
Execute Auto-Image and follow
Auto-Switch Mode
Set Auto-Switch mode
View Auto-Switch mode
Set Auto-Switch priority
View Auto-Switch priority
View memory priority
Output Scaler Rate
Set output rate
View output rate
KEY:
X!
= Input selection
X2!
= Output resolution and rate
X3)
= Auto-Switch mode
X3!
= Input numbers for Auto-Switch priority
ASCII Command
Response
X!
X!
*1!
In
*1
X!
*1%
In
X! •
X!
X! •
*1$
In
1*0A
Img*0
1*1A
Img*1
1*2A
Img*2
E X3)
}
X3)]
AUSW
Ausw
E
AUSW
}
X3)]
E
X3!
X3!
}
P
...
AUSW
Ausw P
1
8
E
P AUSW
}
X3!
1
...
E
}
X3!
O AUSW
1
...
E
X2!
}
1*
RATE
Rate1*
E
1RATE
}
X2!]
1 through 8
See the EDID Emulation and Output Rate table in the IN1806 and IN1808 Series User Guide.
0 = disabled (default), 1 = user defined priority, 2 = input memory priority (most recently
detected input)
1 through 8
Additional Description
]
All
Select audio and video from input
•
1Vid
]
Select the video only from input
]
1Aud
Select the audio only from input
]
Execute an Auto-Image (follows aspect setting).
]
Execute an Auto-Image and fill the output raster.
Execute an Auto-Image and follow the input aspect ratio.
]
Select Auto-Switch mode
View the current Auto-Switch mode.
X3!
X3!
]
X3!
...
Set priority
1
8
priority, from highest to lowest.
View Auto-Switch priority. Lists inputs in order of priority,
X3!
]
8
from highest to lowest.
View Auto-Switch memory priority, from highest to lowest
X3!
]
8
X2!]
Select output resolution and refresh rate
View the output rate.
X!
to the output.
X!
to the output.
X!
to the output.
X3)
.
for input selection. Lists inputs in order of
X2!
.
5
Advertisement
Need help?
Do you have a question about the IN1808 Series and is the answer not in the manual?
Questions and answers