Kenwood NX-5800 Service Manual page 85

Item Condition
Panel tuning
mode
7. 1) Adj item:
Medium [M_LMT]
Trans- Adjust:[****]
mit 2) Adj item:
Power [Low1]→
Limit [Low5]→
[Center3]→
[High2]→
[High6]
PTT : OFF
Press [ ] key to
store the adjust-
ment value.
8. 1) Adj item:
Low [L_LMT]
Trans- Adjust:[****]
mit 2) Adj item:
Power [Low1]→
Limit [Low5]→
[Center3]→
[High2]→
[High6]
PTT : OFF
Press [ ] key to
store the adjust-
ment value.
9. 1) Adj item:
High [H_PWR]
Trans- Adjust:[****]
mit 2) Adj item:
Power [Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
10. 1) Adj item:
Medium [M_PWR]
Trans- Adjust:[****]
mit 2) Adj item:
Power [Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Power
[Medium Transmit meter
Power Limit] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Apply] but-
ton to store the ad-
justment value.
1) Adj item: Power
[Low Transmit meter
Power Limit] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Apply] but-
ton to store the ad-
justment value.
1) Adj item: Power
[High Transmit meter
Power] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Power
[Medium Transmit meter
Power] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Adjustment
Method
Write the value as
followings.
256 (Fixed)
Write the value as
followings.
256 (Fixed)
25W ±1W
7A or less
Note:
[PC test
High Transmit Power
mode]
Is the purpose of the
Press [Apply
custom power (adjust-
All] button to
ment).
store the
This Power must be
adjustment
lower than High trans-
value after all
mit power.
adjustment
points have
been adjusted.
5W ±0.5W
7A or less
Note:
[PC test
In the production, this
mode]
Medium transmit pow-
Press [Apply
er is adjusted at 5W.
All] button to
And E type can't be
store the
adjusted over 5W.
adjustment
(If you adjust over 5W,
value after all
choose High Transmit
adjustment
Power mode.)
points have
been adjusted.
(No.RA017<Rev.003>)1-85
Specifica-
tions
/Remarks