Advertisement
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
Changing Batteries
•
Smoke Detector Battery Change
3 x 1.5v AA
SR-KF
(Lithium)
When the battery is low the LED will flash accompanied by a low volume beep once every 30 seconds.
SR-PVC
1.
2. Remove
3.Insert
SR-SD
new
old
Rotate anti-
batteries
clockwise to
batteries
remove
SR-KF
Press the test button and check that the LED lights and the sounder chimes to confirm the new battery
installation is successful.
SR-PB
Panic Button Battery Change
When the battery is low the LED will glow dimly when the button is pressed. The battery is changed as
follows:
SR-SD
SR-PB
1. Unscrew
2. Open case
3. Remove
old battery
Press the button and check that the LED lights. If the LED lights the new battery installation is
successful.
30
(23)
CR 2032
3 x 1.5v AA
CR 2032
4.
Fit & rotate
clockwise to lock.
CR 2032
3 x 1.5v AA
CR 2032
4. Insert new
battery & replace
cover.
Troubleshooting
•
External Siren
Siren produces a 3 second alarm
when disarmed
• There has been a previous alarm and there might
be an intruder still in the premises.
Siren produces a series of audible pips
when armed or disarmed
• If the Siren produces a series of pips when arming
and disarming this indicates low batteries. Check
your app for confirmation of battery status.
• If the Siren produces a series of pips only when
arming this indicates a tamper fault. Check that
the Siren cover is firmly secured and the tamper
spring on the back of the Siren is fully depressed
when in contact with the wall. If not use suitable
packing material to fill the gap).
Siren produces an interrupted tone when
sounding an alarm
• Low battery warning. Check your app for battery
status. Change batteries (see page 27).
Siren does not respond to Arming or
Disarming
• Siren batteries may be completely exhausted.
Check your app for confirmation of battery status.
See instructions for changing batteries on page
27.
• Siren may not be learnt-in. If Siren produces a
tamper alarm when the cover is removed and the
Siren is OK, learn-in the Siren (see page 11).
• Siren may not be in range of the Smart Hub
Ensure these are within 30m of each other and
relocate devices if required.
Adding the External Siren
• Ensure the dip switch positions are as shown
in the diagram. If the switches are in the wrong
position, please change accordingly
• After changing the
dip switch, turn off the
power for 30 seconds,
then turn the power on
again for the changes to
take effect
Door/Window Contact
Door/Window Contact LED lights up
• Batteries are low or the tamper switch has been
disturbed. Check that the tamper switch spring is
making contact with the mounting surface. If the
tamper switch is OK, please change the battery.
Door/Window Contact does not respond
(14)
to opening when jumper is in the test
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Ins
(DK) Installation.
7
position
1
• Batteries are completely exhausted. Change the
battery.
• The magnet is too far away from the sensor.
Check that the gap between the sensor and
magnet is not greater
3
than 10mm.
PIR Motion
max 10mm
Detector
5
PIR does not respond to motion
• Previous motion may have triggered the PIR
sleep timer, and is preventing subsequent motion
detection. Arm the system and the vacate
protected area for at least 60 seconds before
testing. By pressing the learn/test button the PIR
LED will light up and detect motion for the first
6
minute.
b
PIR Motion Detector is slow to respond
• This is normal. The PIR Motion Detector has
sophisticated false alarm filtering to filter out
a
random fluctuations, and responds to genuine
motion across field of view, the PIR is less
sensitive, when walking directly towards it.
2
a
4
or
7
31
Hide quick links:
Advertisement
