Advertisement
Adding & Using Devices
e batterie - (DE) Batteriewechsel - (NO) Batteribytte -
Reset Key Pad Code
Reset to factory default (0000) using the following steps:
1. Unscrew
CHANGE
BATTERY
SR-KP
3. Hold down number 3 to discharge and then insert the
new battery.
CR 2032
5. Initiliase your Key Pad. See previous page 22.
SR-DC
6. Learn this into your system.
CR 2032
+
Disarmed
Part Armed
SR-PC
Armed
2 x 1.5v AA
Using your Panic Alarm
+
• Press the panic buttons together for 3 seconds to activate
PIN CODE
the alarm.
• Deactivate a panic event by pressing the disarm button
followed by your PIN code.
SR-PIR / PETPIR
If there is a system fault, you will need to press the Arm/
Home Arm button for a second time to "force arm" the
system.
3 x 1.5v AAA
24
Pair / Test button
CHANGE
•
(IT) Associazione/test - (DE) Verbinden/Testen -
BATTERY
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
3
2. Remove
CR 2032
1
CR 2032
4. Replace cover
Pair / Test button
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
1
2 x 1.5v AA
+
PIN CODE
PIN CODE
Panic button
Panic button
>3sec.<
>3sec.<
Press the 2 panic buttons together for
Press the 2 panic buttons together for
3 seconds to activate a panic alarm.
3 seconds to activate a panic alarm.
3 x 1.5v AAA
Panic button
>3sec.<
Press the 2 panic buttons together for
3 seconds to activate a panic alarm.
Adding & Using Devices
Smoke Detector
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
1
Pair / Test button
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
3
Smoke Detector testing should be done on a regular monthly basis. Pressing the test button will make
the LED flash, the audible sounder chime and will send a test signal to the Smart Hub when the button is
released. If nothing happens after pressing the test button, it indicates the batteries will need changing (see
page 26).
Recalibration
The Smoke Detector might need recalibrating after time to ensure it is working at its optimum. This is done
(GB) Setting up - (IT) Configurazione - (DE) Einstellung -
by pressing and holding the test button until the LED flashes and beeps after 10 seconds. The Detector will
(NO) Tilkobling og montering av alarmsentralen - (SE) Driftsättning -
then start its self calibration routine.
(DK) Opsætning.
1
1
Panic Button
Activate an Alarm
Press and hold the red button for at least 3 seconds to activate a panic alarm.
Pair / Test button
(IT) Associazione/test - (DE) Verbinden/Testen -
Silence an Alarm
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
2
Press and hold down the red button for 10 seconds.
1
Silencing the alarm with the Panic Button does not reset the system. If the alarm is armed prior to activation,
the system will re-arm after being silenced with the Panic Button.
Ø 5mm
Resetting the system after a Panic Alarm
The system will require a reset at the Smart Hub after being silenced with the Panic Button. To reset the
Smart Hub unplug the AC power (a) and turn the battery switch off for 10 seconds. Turn the battery switched
back on and plug in the AC power again.
4
(a)
L e a
rn
te ry
B at
ff >
n O
< O
e r
P o w
L A N
•
Smoke Detection
When smoke is detected the device will activate for a minimum of 10 seconds with a two
tone alarm and flashing LED.
7
2
Pressing the test button when in an alarm condition will silence the alarm for 10 minutes. It
will automatically resume smoke detection again after this period.
Testing
4
n
Le ar
Ba tte
ry
n Of
f>
<O
Po w
er
LA N
3
Router
NOT INCLUDED
Ø 5mm
a
<On Off>
b
t e r y
B a t
f f >
n O
< O
(15)
(GB) How does it work - (IT) Come funziona - (DE) Wie es funk
(NO) Hvordan virker det - (SE) Hur fungerar det - (DK) Hvord
SR-KF
(09)
Radio 868MHz
SR-PB
10 secs
Radio 868MHz
SR-EIR
2.3m
110°
Radio 868MHz
25
(GB) Tamper alarm - (IT) Allarme effrazion
(SE) Manipulationslarmet - (DK) Destrukt
a
>3s
Hide quick links:
Advertisement
