Ofs APTOS Installation Instructions Manual

APTOS
DUOFOIL LEGS
INSTALLATION INSTRUCTIONS
DRILL
DRILL
DRILL
TAPE MEASURE
TAPE MEASURE
1/8" DRILL BIT
1/8" DRILL BIT
1/8" DRILL BIT
STEP 1: CHECK BOTTOM SIDE OF TOP FOR PRE BORED MOUNTING HOLES (IF
DONE MOVE TO STEP 4)
STEP 2: IF TOP ORDERED DOES NOT HAVE PREBORED MOUNTING HOLES,
PLACE TOP UPSIDE DOWN ON A PROTECTIVE SURFACE AND LOCATE
STEP 1: CHECK BOTTOM SIDE OF TOP FOR PRE BORED MOUNTING HOLES (IF
TAPE MEASURE
TAPE MEASURE
DUOFOIL LEGS AT A 45 ANGLE TO EDGE OF TOP WITH WIRE CAVITY
FACING TORWARD KNEESPACE AT A DISTANCE OF 8 5/8" FROM EDGE
STEP 2: IF TOP ORDERED DOES NOT HAVE PREBORED MOUNTING HOLES,
OF TOP TO THE CENTER OF THE MOUNTING PLATES BACK EDGE
(SEE ILLUSTRATION BELOW)AND MARK LOCATION OF EACH HOLE USING
MOUNT PLATE HOLES AS LOCATION GUIDE.
STEP 3: AFTER MARKING MOUNTING PLATE HOLE LOCATIONS REMOVE DUOFOIL
LEGS AND PREBORE
LOCATIONS.
STEP 3: AFTER MARKING MOUNTING PLATE HOLE LOCATIONS REMOVE DUOFOIL
STEP 4: ATTACH DUOFOIL LEGS TO BOTTOM SIDE OF TOP (WIRE CAVITY FACING
KNEESPACE) WITH HK-98, ALIGNING HOLES IN MOUNT PLATE WITH
PRE-BORED HOLES IN TOP.
STEP 4: ATTACH DUOFOIL LEGS TO BOTTOM SIDE OF TOP (WIRE CAVITY FACING
STEP 5: LEVELER IN BOTTOM OF DUOFOIL LEGS CAN BE ADJUSTED OUT
UPTO 1" TO LEVEL THE TOP AS NEEDED.
STEP 5: LEVELER IN BOTTOM OF DUOFOIL LEGS CAN BE ADJUSTED OUT
INSTRUCTIONS
INSTRUCTIONS
DUOFOIL LEGS
DUOFOIL LEGS
1. Check bottom side of top for pre-bored mounting holes. (If done, move to
Step 4.)
2. If top ordered does not have pre-bored mounting holes, place top upside
down on a protective surface and locate duofoil standoffs at a 45° angle to
edge of top with wire cavity facing toward kneespace at distance of 8 5/8"
from edge of top to the center of the mounting plates back edge (see
DONE MOVE TO STEP 4)
illustration below) and mark location of each hole using mount plate holes
as location guide.
PLACE TOP UPSIDE DOWN ON A PROTECTIVE SURFACE AND LOCATE
3. After marking mounting plate hole locations, remove duofoil legs and pre-
DUOFOIL LEGS AT A 45 ANGLE TO EDGE OF TOP WITH WIRE CAVITY
bore 1/8" diameter x 13/16" deep holes at previously marked locations.
FACING TORWARD KNEESPACE AT A DISTANCE OF 8 5/8" FROM EDGE
4. Attach duofoil legs to bottom side of top (wire cavity facing kneespace) with
OF TOP TO THE CENTER OF THE MOUNTING PLATES BACK EDGE
(SEE ILLUSTRATION BELOW)AND MARK LOCATION OF EACH HOLE USING
HK-71, aligning holes in mount plate with pre-bored holes in top.
1/8" X 13/16" DEEP HOLES AT PREVIOUSLY MARKED
MOUNT PLATE HOLES AS LOCATION GUIDE.
5. Leveler in bottom of duofoil legs can be adjusted out, up to 1", to level the
top as needed.
LEGS AND PREBORE 1/8" X 13/16" DEEP HOLES AT PREVIOUSLY MARKED
LOCATIONS.
KNEESPACE) WITH HK-98, ALIGNING HOLES IN MOUNT PLATE WITH
PRE-BORED HOLES IN TOP.
UPTO 1" TO LEVEL THE TOP AS NEEDED.
WIRE CAVITY
WIRE CAVITY
WIRE CAVITY
INSTRUCTION SHEET # 2555INS
Dwg:
Dwg:
STEP 2 & 3: TO LOCATE LEGS IN
STEPS 2 & 3: TO LOCATE LEGS IN
NON PREBORED TOP
NON PRE-BORED TOP
STEP 2 & 3: TO LOCATE LEGS IN
NON PREBORED TOP
45°
45°
45°
8.625
8.625
8.625
PART # 1711258
Rev:
Rev:
45°
45°
45°
8.625 8.625
8.625