Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ofs Slate collaborative
Summary of Contents for Ofs Slate collaborative
- Page 1 Slate collaborative assembly...
-
Page 2: Table Of Contents
Slate collaborative assembly Table of contents Tools required and parts Step 1: Position lower credenza unit Step 2: Attach upper credenza unit Step 3: Attach slide-out markerboards Step 4a: Attach end storage cabinets Step 4b: Attach end panels Step 5a: Attach overlay assemblies... -
Page 3: Tools Required And Parts
Slate collaborative assembly Tools required Drill Tape measure Level Parts NOTE: Not all parts listed below will be included with your selection. Some features are optional and will only be present if selected with your Slate set-up. End panel End storage cabinet (optional) Lower credenza unit ofs.com imagine a place® 800.521.5381 Assembly instructions... - Page 4 Slate collaborative assembly Parts continued Markerboard (optional) End cap Drawer storage unit (optional) Upper credenza unit (shown with optional markerboard attachment) Overlay assembly (shown with optional drawer or worksurface attachment) ofs.com imagine a place® 800.521.5381 Assembly instructions...
-
Page 5: Step 1: Position Lower Credenza Unit
Slate collaborative assembly Step 1: Position lower credenza unit Place the lower credenza unit into it’s permanent location. The workspace assembly will be too heavy to move once it is fully assembled. Ensure that the credenza unit is level at this time. -
Page 6: Step 2: Attach Upper Credenza Unit
Slate collaborative assembly Step 2: Attach upper credenza unit Place the upper credenza unit onto the lower credenza unit. Position both units such that all outside surfaces are flush with one another. Also, make sure the cord management hole in the center of the units are aligned with each other. -
Page 7: Step 3: Attach Slide-Out Markerboards
Slate collaborative assembly Step 3: attach slide-out markerboards NOTE: The markerboards are an optional feature. Disregard this step if it is not part of your selection. Begin by identifying all parts of the drawer slide. The inner track is attached to the markerboard, the outer track and slide are mounted to the upper credenza. Attach markerboard by inserting inner track onto slide. Making sure both parts are aligned into each other’s groove, slide markerboard in completely until it reaches the slide stop. -
Page 8: Step 4A: Attach End Storage Cabinets
Slate collaborative assembly Step 4a: Attach end storage cabinets (10) #8 x 1 1/4" Note: This step is instructed for units with end storage cabinets. If end panels are part of your selection, see step 4b. Position the end storage cabinet next to the credenza assembly. Level storage cabinet and make sure all surfaces are aligned and flush with one another. -
Page 9: Step 4B: Attach End Panels
Slate collaborative assembly Step 4b: Attach end panels (10) #8 x 1 1/4" Note: This step is instructed for units with end panels. If end storage cabinets are part of your selection, see step 4a. Position the end panel next to the credenza assembly. Level panel and make sure all surfaces are aligned and flush with one another. Attach panel by fastening the supplied screws from the HK-48 kit through the credenza assembly and into the panel as shown above. -
Page 10: Step 5A: Attach Overlay Assemblies
Slate collaborative assembly Step 5a: Attach overlay assemblies NOTE: The overlay assembly size will vary depending on your selection. The instructions detailed below are for all sizes that will have a drawer storage unit or extension worksurface attached to it. If the markerboards are extended, slide them completely back in. Take note of the notched support rail on the top of the credenza assembly and the support rail and cleats on the underside of the overlay assembly. -
Page 11: Step 5B: Attach Overlay Assemblies
Slate collaborative assembly Step 5b: Attach overlay assemblies Note: The overlay assembly size will vary depending on your selection. The instructions detailed below are for all sizes that are plain and will have nothing attached to it. Take note of the notched support rail on the top of the credenza assembly and the support rail and cleats on the underside of the overlay assembly. Lift overlay assembly up and onto the credenza assembly, lining up the cleats with the notches on the support rail as shown above. -
Page 12: Step 6: Attach Drawer Storage Unit
Slate collaborative assembly Step 6: Attach drawer storage unit Note: The drawer storage unit is an optional feature. Disregard this step if it is not part of your selection. Begin by removing the drawer boxes from the storage unit. Drawer boxes can be removed by pulling box slightly out and locating the plastic lock clips on the side of the inner tracks of the drawer slide. -
Page 13: Step 7: Attach Extension Worksurface
Slate collaborative assembly Step 7: Attach extension work surface NOTE: The extension worksurface is an optional feature. Disregard this step if it is not part of your selection. Attach the apron rails to the table base using the supplied screws from the HK-10 kit at the spacing specified above. Slide table base and rail assembly directly against the credenza assembly. - Page 14 Slate collaborative assembly Place the worksurface onto the table base assembly and slide directly against the overlay assembly. Center the worksurface with the table base and attach to the overlay by fastening the supplied screws from the HK-55 kit through the worksurface and into the overlay.
-
Page 15: Step 8: Attach End Caps
Slate collaborative assembly Step 8: Attach end caps Place end cap on top of workspace and carefully press inward until the end cap has reached the support rails on the overlay assemblies. Repeat for remaining end cap. Assembly is now complete.
Need help?
Do you have a question about the Slate collaborative and is the answer not in the manual?
Questions and answers