PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT! If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-3377 before attempting to use this product; otherwise injury may occur. Winco assumes no responsibility for damage or injury caused by improper assembly, installation, use, or maintenance of these products.
LIMITED ONE YEAR COMPLETE PRODUCT WARRANTY: Winco, Inc. warrants the complete product for one (1) year. At Winco Inc. sole discretion, it may repair or replace any components freight free that are found to be defective during the fi rst year. Winco, Inc. shall not be liable for any labor, or any other costs incurred as a result of or in conjunction with a warranty claim.
4. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to an authorized Winco service center. 5. DO NOT carry or pull this product by power supply cord or use the cord as a handle.
Page 5
No adapter should be used with this product. For an added level of safety; Winco recommends the use of a 120 volt GFCI (ground fault circuit interruptor) outlet.
CAUTION to avoid cutting your skin or damaging the product. • If you have questions about your assembly or if the product is damaged in ANY way, please contact Winco Customer Support at 1-800-237-3377. Weight Capacities Models 2570–2573, 2577-2578, & 2587-2588: •...
Seat Installation 2570-2575, 2587-2588 WARNING Failure to completely tighten the seat mounting screws COULD RESULT IN SERIOUS INJURY. FIG. 1 Models 2570 and 2571 (FIG. 1) Position Chair Frame in upright position. Check tight- ness of all installed screws, bolts and nuts in case they loosened during shipping.
Arm Installation - All models 1. If the Arm Assembly has not yet been installed, insert it into the Receiving Tube on Seat Frame Assembly. (This applies to any style arm assembly) •ALWAYS make sure that the slot in the Arm Assembly faces the Knob installed on the receiving tube.
Cabinet Assembly Models 2570, 2572, & 2574 Remove the drawer from the cabinet. Attach the Welded Cabinet Support to bottom of Cabinet by installing (4) 2” screws through (4) holes in the Welded Cabinet Support. Install washers and locknuts on the screws inside the cabinet. (FIG. 1). Use the supplied wrench to hold nuts inside of cabinet &...
Models 2577 & 2578 Seat Height Set-up and/or Adjustment The seat height of your 577-578 Designer Blood Drawing Chair can be adjusted during setup. CAUTION: The Seat Assembly is VERY HEAVY. To adjust the height; the chair must be supported by someone that can LIFT OVER 50 LBS.
“PR” & “P2” - Optional Pivot Arm (see models listed below) **If ordered with “L” shaped arm follow arm assembly instructions on page 8** Models 2570-2571-2572-2573-2574-2575 PR and 2571-2573-2575 P2 Your Pivot Arm assembly may be confi gured in one of two (2) directions: •...
Parts Guide & List C O M M O N P A R T S - f o r a l l c h a i r s Flip-Up Urethane Arm Rest, black ........708010 (standard right armrest for all Blood Drawing Chairs) Small Urethane Arm Rest, black ..........
Parts Guide & List **ALL Upholstered Parts** ....Call for Special Part Numbers (seat, back, arm pads, cabinet pad, etc...) 2 5 7 2 Main Frame ..............226101 Arm Support Assembly ..........226270 Seat & Back Frame ............226300 Welded Cabinet Support Assm ........226340 Cabinet w/drawer &...
Parts Guide & List 2 5 7 5 Main Frame ..............226102 Arm Support Assembly ..........226270 Welded Arm Column ...... 226255 (for Small Arm, Left) Seat & Back Frame ............226320 Lock Nuts, ( ........... 566204 for seat screws) Adjustable Glide Foot............500350 *With Pivot-Swing Arm Option: *Upholstered Arms.
Parts Guide & List 2 5 8 7 - 2 5 8 8 RIGHT SIDE, Flip-Up Urethane Arm Parts: Arm Support Assembly, offset (no ST brkts) ....226290 (FOR STANDARD STYLE CHAIRS WITHOUT A SIDE TABLE) Arm Support Assembly, offset (ST brkts) ..... 226280 Side Table w/ Cover Assm Kit (RIGHT side ONLY) ..
Page 16
5516 Southwest 1st Lane Ocala, FL 34474 1-800-237-3377 / 352-854-2929 / Fax: 352-854-9544 e-mail: customerservice@wincomfg.com Visit us on the web: www.wincomfg.com #006020 Rev E 02-08-10...