Ingersoll-Rand PD30*-*-B Operator's Manual

OPERATOR'S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material
options.
637303-XXX for fluid section repair with seats (see page 4).
637303-XX for fluid section repair without seats (see page 4).
NOTE: This kit also contains several air motor seals which will
need to be replaced.
637302 for air section repair (see page 6).
67089-X major air valve assembly (see page 7).
PUMP DATA
Models . . . . . . see Model Description Chart for "-XXX".
Pump Type . . . Metallic Air Operated Double Diaphragm
Material . . . . . see Model Description Chart.
Weight
PD30A-XAX-XXX-B () . . . . . . . . . . . . 113 lbs (51.3 kgs)
PD30A-XCX-XXX-B () . . . . . . . . . . . . 197 lbs (89.4 kgs)
PD30A-XHX-XXX-B () . . . . . . . . . . . . 203 lbs (92.1 kgs)
PD30A-XSX-XXX-B () . . . . . . . . . . . . 203 lbs (92.1 kgs)
(add 40 lbs [18.1 kg] for stainless steel air motor section)
Maximum Air Inlet Pressure
Ball check models . . . . . . . . . . . . . . . 120 psig (8.3 bar)
Maximum Material Inlet Pressure . . 10 psig (0.69 bar)
Maximum Outlet Pressure
Ball check models . . . . . . . . . . . . . . . 120 psig (8.3 bar)
Maximum Flow Rate
(flooded inlet)
Ball check models . . . . . . . . . . . . . . . . . . . . . . . 275 gpm (1041 lpm)
Displacement / Cycle @ 100 psig . . . 2.8 gal. (10.6 lit.)
Maximum Particle Size
Ball check models . . . . . . . . . . . . . . . 3/8" dia. (9.5 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . . . . . . -60

Hytrel . . . . . . . . . . . . . . . . . . . -20
Nitrile . . . . . . . . . . . . . . . . . . . . . 10

Kynar PVDF . . . . . . . . . . . . . . 10

Santoprene . . . . . . . . . . . . . . -40
PTFE . . . . . . . . . . . . . . . . . . . . . 40

Viton . . . . . . . . . . . . . . . . . . . . -40
Dimensional Data . . . . . . . . . . . . see page 8
Mounting Dimension . . . . . . . . . . . 10-5/32" x 12-1/16"
Noise Level @ 70 psig, 50 cpm

Tested with 67263 muffler assembly installed.

The pump sound pressure levels published here have been updated to an Equivalent
Con tinu ous Sound Level (LA ) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP
eq
S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain combinations
may not be recommended, consult a representative or the factory if you have ques-
tions concerning availability.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506


(800) 495-0276 FAX (800) 892-6276
arozone.com
3" DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
OPERATING OR SERVICING THIS EQUIPMENT.
   
to 280 F (-51 to 138 C)
  º 
to 180 F (-29 to 82
  º 
to 180 F (-12 to 82
   
to 200 F (-12 to 93
  
to 225 F (-40 to 107
   
to 225 F (4 to 107
  
to 350 F (-40 to 177
(258 mm x 306 mm)
 
. . . . . . 83.0 dB(A)
© 2016 CCN 99756587
MODEL DESCRIPTION CHART
AIR MOTOR / AIR CAP MATERIAL
A - Aluminum
S - Stainless Steel
THREAD
A - NPTF
FLUID CAPS & MANIFOLD MATERIAL
A - Aluminum
C - Cast Iron
HARDWARE MATERIAL
P - Plated Steel
SEAT MATERIAL
A - Santoprene
C)
C - Hytrel
C)
E - Carbon Steel
C)
F - Aluminum

C)
G - Nitrile
C)
BALL MATERIAL

C)
A - Santoprene
C - Hytrel
G - Nitrile
DIAPHRAGM MATERIAL
A - Santoprene
C - Hytrel
G - Nitrile
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: MODEL # PD30A-ACS-SAA-B
FLUID SECTION SERVICE KIT # 637303-AA
PD30X-X-B
RELEASED:
REVISED:
(REV: U)
Figure 1
P D30 X - X X X - X X X - B
B - BSP
H - Hastelloy
S - Stainless Steel
S - Stainless Steel
H - Hard 440 Stainless Steel
K - Kynar PVDF
L - Hastelloy
S - 316 Stainless Steel
T - PTFE
V - Viton
L - Long Life PTFE
T - PTFE / Santoprene
V - Viton
PD30X - XXX - X X X - B
637303 - X X
Ball
8-14-98
10-28-16
Diaphragm