Table of Contents
Advertisement
Quick Links
r
Tribomatic
500 Manual Powder
Spray Gun
Customer Product Manual
Part 237467D02
Issued 11/07
For parts and technical support, call the Industrial Coating
Systems Customer Support Center at (800) 433-9319 or
contact your local Nordson representative.
This document is subject to change without notice.
Check http://emanuals.nordson.com for the latest version.
NORDSON CORPORATION AMHERST, OHIO USA
Advertisement
Table of Contents
Related Manuals for Nordson Tribomatic 500
Summary of Contents for Nordson Tribomatic 500
-
Page 1: Spray Gun
For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative. This document is subject to change without notice. Check http://emanuals.nordson.com for the latest version. NORDSON CORPORATION AMHERST, OHIO USA... -
Page 2: Table Of Contents
....... . . Contact Us Notice This is a Nordson Corporation publication which is protected by copyright. Nordson Corporation welcomes requests for information, comments, and Original copyright date 1997. No part of this document may be inquiries about its products. -
Page 3: Safety
Regulations and Approvals Make sure all equipment is rated and approved for the environment in which it is used. Any approvals obtained for Nordson equipment will be voided if instructions for installation, operation, and service are not followed. All phases of equipment installation must comply with all federal, state, and local codes. -
Page 4: Personal Safety
Clean, maintain, test, and repair equipment according to the instructions in your equipment documentation. Use only replacement parts that are designed for use with original equipment. Contact your Nordson representative for parts information and advice. Part 237467D02 E 2007 Nordson Corporation... -
Page 5: Grounding
Disconnect and lock out electrical power. Close pneumatic shutoff valves and relieve pressures. Identify the reason for the malfunction and correct it before restarting the equipment. Disposal Dispose of equipment and materials used in operation and servicing according to local codes. Part 237467D02 E 2007 Nordson Corporation... -
Page 6: Description
Friction electrostatically charges the powder particles as they flow through the sleeves. The 6 meter spray gun is used with a Nordson 3-gauge Tribomatic II control unit and modular Tribomatic powder pump, which are sold separately. -
Page 7: Specifications
5. Outer charge sleeve 8. Pattern adjust sleeve 3. Diffuser 6. Pattern adjuster retainer 9. Cable Specifications Length: 521 mm (20.5 in.) maximum Weight: 0.5 kg (1.1 lbs) (without cable) Capacity: 4.5−8 kg (10−18 lbs) per hour Part 237467D02 E 2007 Nordson Corporation... -
Page 8: Installation
5. Bundle the powder feed hose, diffuser air tubing, and trigger cable together with spiral-cut plastic tubing. To prevent damage to the hose, tubing, and cable, keep them away from moving equipment and off the floor. Part 237467D02 E 2007 Nordson Corporation... - Page 9 5. Diffuser 9. Powder feed hose 2. Flow-rate air fitting 6. Spiral-cut tubing 10. Powder pump 3. GUN OUTPUT receptacle 7. Clamps 11. Black 6-mm air tubing 4. Blue 6-mm air tubing 8. Cable Part 237467D02 E 2007 Nordson Corporation...
-
Page 10: Operation
Adjust these pressures to obtain the desired results as follows: Increase flow-rate air pressure to increase film build; decrease pressure to decrease film build. Increase diffuser air pressure to increase electrostatic charging. Decrease diffuser pressure to decrease charging. Part 237467D02 E 2007 Nordson Corporation... -
Page 11: Pattern Control
Refer to the pump manual for disassembly instructions. 5. Check all equipment ground connections. Make sure all equipment in the spray area is connected to a true earth ground. Part 237467D02 E 2007 Nordson Corporation... -
Page 12: Troubleshooting
Follow the safety instructions in this document and all other related documentation. These procedures cover only the most common problems that you may encounter. If you cannot solve the problem with the information given here, contact your local Nordson representative for help. Problem Possible Cause Corrective Action 1. - Page 13 Flow-rate air pressure too low Increase the flow-rate air pressure. powder flow Blockage in system Clean the pickup tube, pump, feed hose, diffuser, and gun. Make sure the powder is not damp. Check the air dryer. Part 237467D02 E 2007 Nordson Corporation...
-
Page 14: Repair
6. Push, then pull the outer charge sleeve (9) out of the gun body. 7. Remove the O-ring (8) from the outer charge sleeve. If it is undamaged, it can be used on the new charge sleeve. Part 237467D02 E 2007 Nordson Corporation... -
Page 15: Assembly
4. Slide the pattern adjuster retainer over the outer charge sleeve support. Push the outer charge sleeve support over the outer charge sleeve and into the body until it is seated. 5. Install the deflector on the end of the inner charge sleeve assembly. Part 237467D02 E 2007 Nordson Corporation... -
Page 16: Outer Charge Sleeve Support And Pattern Adjust Sleeve Replacement
Figure 5 Outer Charge Sleeve Support and Pattern Adjust Sleeve Replacement 1. Outer charge sleeve support 3. Deflector 5. O-ring (black) 2. Pattern adjuster retainer 4. Pattern adjust sleeve 6. O-ring (red) Part 237467D02 E 2007 Nordson Corporation... -
Page 17: Handle, Trigger, And Cable Replacement
(15) from the handle. If replacing the cable (9), remove the screws, washers, and actuator from the trigger switch. 6. Unscrew the pivot (17), then remove it and the trigger (16). Remove the screw (14) to replace the trigger spring. Part 237467D02 E 2007 Nordson Corporation... -
Page 18: Assembly
7. Arrange the wires so they will not be pinched between the handle halves. Make sure the cable molding fits properly into the bottom of the handle. 8. Install the cover and tighten the captive screws. Part 237467D02 E 2007 Nordson Corporation... -
Page 19: Parts
A dash (—) is used when the part number applies to all parts in the illustration. The number in the Part column is the Nordson Corporation part number. A series of dashes in this column (- - - - - -) means the part cannot be ordered separately. -
Page 20: Gun Parts
Gun Parts See Figure 7. Item Part Description Quantity Note — 1076394 GUN, manual, Tribomatic 500, 6 meter cable 302422 S HANGER, manual gun 304390 S KIT, handle 132334 S PIVOT, trigger 982370 S SCREW, pan head, M2 x 25... - Page 21 Tribomatic 500 Manual Powder Spray Gun Figure 7 Handle, Trigger, and Cable Replacement Part 237467D02 E 2007 Nordson Corporation...
-
Page 22: Inner Charge Sleeve Kit
KIT, outer charge sleeve support 940184 S O-RING, silicone, conductive, 0.75 x 0.875 in. 941231 S O-RING, silicone, 1.188 x 1.375 x 0.094 in. 326656 S RETAINER, pattern adjuster Figure 9 Inner Charge Sleeve Kit Part 237467D02 E 2007 Nordson Corporation... -
Page 23: Diffuser Kit
Diffuser Kit Handle Kit Item Part Description Quantity Note — 304390 KIT, handle 981626 S SCREW, captive, M4 x 12 940060 S O-RING, Viton, 0.125 x 0.250 x 0.063 in. Figure 11 Handle Kit Part 237467D02 E 2007 Nordson Corporation... - Page 24 Tribomatic 500 Manual Powder Spray Gun Part 237467D02 E 2007 Nordson Corporation...
Need help?
Do you have a question about the Tribomatic 500 and is the answer not in the manual?
Questions and answers