Siemens SPC3 Hardware Description page 18

PROFIBUS Interface Center
Address Name
Intel
/Motorola
16H R_TS_Adr
7..0
17H reserved
18H 19H R_User_Wd_Value
7..0
19H 18H R_User_Wd_Value
..8
1AH R_Len_Dout_Puf
1BH R_Dout_buf_Ptr1
1CH R_Dout_buf_Ptr2
1DH R_Dout_buf_Ptr3
1EH R_Len_Din_buf
1FH R_Din_buf_Ptr1
20H R_Din_buf_Ptr2
21H R_Din_buf_Ptr3
22H reserved
23H reserved
24H R Len Diag buf1
25H R Len Diag buf2
26H R_Diag_Puf_Ptr1
27H R_Diag_Puf_Ptr2
28H R Len Cntrl Pbuf1
29H R Len Cntrl Puf2
2AH R Aux Puf Sel
2BH R_Aux_buf_Ptr1
2CH R_Aux_buf_Ptr2
2DH R_Len_SSA_Data
2EH R SSA buf Ptr
2FH R_Len_Prm_Data
30H R_Prm_buf_Ptr
31H R_Len_Cfg_Data
32H R Cfg Buf Ptr
33H R_Len_Read_Cfg_Data
34H R_Read_Cfg_buf_Ptr
35H reserved
36H reserved
37H reserved
38H reserved
39H R_Real_No_Add_Change
3AH R_Ident_Low
3BH R_Ident_High
3CH R_GC_Command
3DH R_Len_Spec_Prm_buf
Figure 4.4: Assignment of the Organizational Parameters
Page 16
2003/04
SPC3
Bit No. Significance
Set up station address of the relevant SPC3
Pointer to a RAM address which is presetted with 0FFH
Based on an internal 16-bit wachdog timer, the user is
monitored in the DP_Mode.
15
Length of the 3 Dout buffers
Segment base address of Dout buffer 1
Segment base address of Dout buffer 2
Segment base address of Dout buffer 3
Length of the 3 Din buffers
Segment base address of Din buffer 1
Segment base address of Din buffer 2
Segment base address of Din buffer 3
Preset with 00H.
Preset with 00H.
Length of Diag buffer 1
Length of Diag buffer 2
Segment base address of Diag buffer 1
Segment base address of Diag buffer 2
Length of Aux buffer 1 and the control buffer belonging to it,
for example, SSA-Buf, Prm-Buf, Cfg-Buf, Read-Cfg-Buf
Length of Aux-Buffer 2 and the control buffer belonging to
it, for example, SSA-Buf, Prm-Buf, Cfg-Buf, Read-Cfg-Buf
Bit array, in which the assignments of the Aux-buffers ½ are
defined to the control buffers, SSA-Buf, Prm-Buf, Cfg-Buf
Segment base address of auxiliary buffer 1
Segment base address of auxiliary buffer 2
Length of the input data in the Set_Slave_Address-buffer
Segment base address of the Set_Slave_Address-buffer
Length of the input data in the Set_Param-buffer
Segment base address of the Set_Param-buffer
Length of the input data in the Check_Config-buffer
Segment base address of the Check_Config-buffer
Length of the input data in the Get_Config-buffer
Segment base address of the Get_Config-buffer
Preset with 00H.
Preset with 00H
Preset with 00H.
Preset with 00H.
This parameter specifies whether the DP slave address may
again be changed at a later time point.
The user sets the parameters for the Ident_Low value.
The user sets the parameters for the Ident_High value.
The Global_Control_Command last received
If parameters are set for the Spec_Prm_Buffer_Mode (see
mode register 0), this cell defines the length of the param
buffer.
V1.3 SPC3 Hardware Description
Copyright (C) Siemens AG 2003. All rights reserved.