Table of Contents
Advertisement
Quick Links
I INSTA A LLATION, SE
ERVIC
E AND
INS
STRUC
CTIONS
PHA
ARMAV
AVALVE
INOXPA,
I
, S.A.
c/Tel
lers, 54 A
Aptdo. 17
E-
-17820 Ba
anyoles
Girona (S
G
Spain)
Tel.: (
(34) 972
- 57 52 0
Fax.:
(34) 972
- 57 55 0
Email:
inoxpa@
@inoxpa.co
w
www.inoxp
pa.com
D MAIN
NTENAN
S
E
4
00
02
om
ORIGI
INAL MAN
NUAL'S T
NCE
TRANSLAT
TION
10.320.
30.01EN
ED.
2009/09
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for INOXPA PHARMAVALVE
Summary of Contents for INOXPA PHARMAVALVE
- Page 1 I INSTA A LLATION, SE ERVIC E AND D MAIN NTENAN STRUC CTIONS ARMAV AVALVE INOXPA, , S.A. c/Tel lers, 54 A Aptdo. 17 -17820 Ba anyoles Girona (S Spain) Tel.: ( (34) 972 - 57 52 0 Fax.: (34) 972...
- Page 2 EC DECLARATION OF CONFORMITY (In accordance with Directive 98/37/EC, annex II, part A) INOXPA, S.A. We, the manufacturer: c/ Telers, 54 17820 Banyoles (Girona) - SPAIN Hereby declare that the products VALVE PHARMAVALVE 2009 Year of Name Type Manufacture conform with the provisions of the Council Directives:...
-
Page 3: Safety
Commitment to safety at the workplace. Protective goggles requirement. 1.4. GENERAL SAFETY INSTRUCTIONS Read the instruction manual carefully before installing and starting up the valve. Contact INOXPA in case of doubt. 1.4.1. During the installation. Technical Specifications of Chapter 8 should always be observed. -
Page 4: Guarantee
The use of other parts will exempt the manufacturer from any liability. The service terms can only be changed with prior written authorization from INOXPA. Please do not hesitate to contact us in case of doubts or if more complete explanations are required on specific data (adjustments, assembly, disassembly, etc.). -
Page 5: Table Of Contents
2. Table of Contents Safety 1.1. Instruction manual ......................3 1.2. Start-up instructions ......................3 1.3. Safety ..........................3 1.4. General safety instructions ....................3 1.5. guarantee ........................4 Table of Contents Delivery and Installation ... -
Page 6: Delivery And Installation
On receipt of the valve check to verify that it agrees with the delivery note. INOXPA inspects all its equipment before packing but we cannot guarantee that the goods will arrive undamaged to the user. For this reason, the valve and any other components received should be checked and, if found not to be in good condition and/or not complete the carrier should submit a report as soon as possible. -
Page 7: Identification
2 – NC PNEUMATIC 3 – TANK-BOTTOM NC PNEUMATIC 4 – NO PNEUMATIC 5 – TANK-BOTTOM NO PNEUMATIC 6 – A/A PNEUMATIC 7 – TANK-BOTTOM A/A PNEUMATIC VALVE TYPE 5 - PHARMAVALVE VALVE V1 – DIAPHRAGM VALVE ED. 2009/09 /... -
Page 8: Location
If there are accessories such as position sensors, travel limits, etc., you must allow an addition space for disassembly of these elements. 3.6. FLOW DIRECTION PHARMAVALVE valves can combine the drives with various types of bodies as described below. The flow direction in L-type bodies can be as shown in figures below. The flow in direction is the recommended direction, as there is less pressure loss and fewer dead zones, due to the direction of closure. -
Page 9: Inspecting And Checking
The welding work can only be carried out by persons qualified, trained and equipped with the necessary means to carry out this work. Disassemble the valve before starting the welding work. 3.9.1. PHARMAVALVE - Butt Weld connections Assembly and disassembly •... -
Page 10: Air Connection To Actuator
• Connect and check the air connections as needed: Double or Single acting • INOXPA valves are supplied with Ø4 tube connections and a silencer in S/A actuators. Technical • Bear in mind the quality of the compressed air in accordance with the specifications described in chapter 8 Specifications. -
Page 11: Start-Up
Never place your fingers inside the casing when a pneumatic actuator has been fitted. Do not modify the operating parameters for which the valve has been designed without written prior authorization from INOXPA. Danger of burns! Do not touch the valve or pipes when hot liquids are circulating or when cleaning and/or sterilisation are being carried out. -
Page 12: Operating Problems: Causes And Solutions
5. Operating problems: Causes and solutions PROBLEM CAUSE/EFFECT SOLUTION • Replace the diaphragm. • Replace the diaphragm with one of a different material and more appropriate to the product. The diaphragm or guide bushing have become worn, THE MOVEMENT OF deteriorated, or blocked up. -
Page 13: Maintenance
50 hours of exposure. • For EPDM diaphragms constantly subjected to steam, check every 250 hours. (use an on/off valve before the PHARMAVALVE to prolong the life of the EPDM diaphragm) Maintenance after a leak Replace at the end of the process. -
Page 14: Cleaning
6.2.2. Storage Storage of the valves should be carried out in an enclosed area, under the following conditions: Temperature from 15ºC to 30ºC Relative humidity <60% Open-air storage of the equipment is NOT allowed. 6.2.3. Spare parts To request spare parts, it is necessary to indicate the type of valve, the position and the description of the part which can be Technical Specifications found in the chapter. -
Page 15: Assembly And Disassembly
In order to prevent this, use connection type B (threaded diaphragm), which holds the diaphragm better. Consult Inoxpa before replacing one diaphragm type with another. Proceed with caution. There is danger of personal injury. -
Page 16: Disassembly / Assembly Of The Pneumatically Actuated Valve
In order to prevent this, use connection type B (threaded diaphragm), which holds the diaphragm better. Consult Inoxpa before replacing one diaphragm type with another. ED. 2009/09 /... -
Page 17: Technical Specifications
8. Technical Specifications VALVE GENERAL DATA Maximum operating pressure (bar/PSI) Manual actuation Pneumatic actuation EPDM/VMQ PTFE EPDM/VMQ PTFE 7 bar /101 7 bar /101 7 bar /101 7 bar /101 DN ½” 7 bar /101 7 bar /101 7 bar /101 7 bar /101 DN 1”... -
Page 18: Valve Dimensions
8.1. VALVE DIMENSIONS ED. 2009/09 /... - Page 19 1/2" 1" 1 1/2" F Ø55 Ø63 Ø63 Manual Actuator G 45‐56 65‐72 64‐74 Pneumatic H Ø42 Ø77.5 Ø94.5 Actuator I 60 69 90 J TC50.5 TC77.5 TC77.5 k 82 124 124 L 41 62 62 M 19.5 32 37.5 ...
-
Page 20: Section And Parts List
8.2. SECTION AND PARTS LIST 8.2.1. Section and parts list MANUALLY ACTUATED VALVE POSITION DESIGNATION MATERIAL QUANTITY Body AISI 316L Nut support AISI 316L Handle AISI 316 Diaphragm Diaphragm shaft AISI 316 Support bushing AISI 316 Guide bushing PTFE Bearing bushing AISI 316 O-ring O-ring... - Page 21 8.2.2. Section and parts list PNEUMATIC ACTUATION POSITION DESIGNATION MATERIAL QUANTITY Casing CF 3M Actuator casing AISI 316L Diaphragm Spring AISI 302 Piston shaft AISI 316L Diaphragm shaft AISI 316L Spring guide Guide bushing PTFE R 1/8" straight connector R 1/8" Silencer O-ring O-ring O-ring...
- Page 22 NOTES...
- Page 23 NOT TES...
- Page 24 SAINT PETERSBURG Тel/Fax: 78126221626/78126221926 e-mail: spb@inoxpa.com In addition to our branch offices, INOXPA operates with an independent distributor network which encompasses a total of more than 50 countries throughout the world. For more information consult our web page: www.inoxpa.com This information is a guideline only. We reserve the right to modify any material or characteristic without prior notice.
Need help?
Do you have a question about the PHARMAVALVE and is the answer not in the manual?
Questions and answers