Related Manuals for AGA marvel ML15CRS1XS
Summary of Contents for AGA marvel ML15CRS1XS
- Page 1 Installation Operation and Maintenance Instructions Ice Machine ML15CRS1XS ML15CRS1XB ML15CRP1XP...
-
Page 2: Table Of Contents
Installation Operation and Maintenance Instructions Contents Service Intro Troubleshooting Warranty Safety Obtaining Service Safety and Warning Disposal and Recycling Installation Environmental Requirements Electrical Cutout Dimensions Product Dimensions Side by Side Installation Water Hookup Anti-Tip Bracket General Installation Overlay Door Panel Dimensions Overlay Door Panel Installation Grille Installation Door Swing... - Page 3 Installation Operation and Maintenance Instructions Welcome to the Marvel Experience Congratulations on adding a new Marvel crescent ice maker to your home and thank you for choosing our quality American-built product. You’ll enjoy years of crescent ice in the comfort and convenience of your home, backed by our full worry-free warranty. We are thrilled to welcome you to our growing community of Marvel owners, who trust in our products and our support.
-
Page 4: Safety And Warning
Installation Operation and Maintenance Instructions Safety and Warning Disposal and Recycling DANGER NOTICE Please read all instructions before installing, operating, or RISK OF CHILD ENTRAPMENT. Before you throw away servicing the appliance. your old refrigerator or freezer, take off the doors and leave shelves in place so children may not easily climb inside. -
Page 5: Electrical
Installation Operation and Maintenance Instructions Electrical Cutout Dimensions PREPARE SITE WARNING Your U-Line product has been designed for either free-standing or built-in installation. When built-in, your unit does not require SHOCK HAZARD — Electrical Grounding Required. Never additional air space for top, sides, or rear. However, the front attempt to repair or perform maintenance on the unit until grille must NOT be obstructed, and clearance is required for an the electricity has been disconnected. - Page 6 Installation Operation and Maintenance Instructions Product Dimensions - ML15CRS1XS & ML15CRS1XB Not Including Handle *Add 3/4" To Depth For Water Line Clearance...
-
Page 7: Product Dimensions
Installation Operation and Maintenance Instructions Product Dimensions - ML15CRP1XP Includes " (20 mm) Overlay Panel *Add 3/4" To Depth For Water Line Clearance... - Page 8 Installation Operation and Maintenance Instructions Side-by-Side Installation 3. Place bracket over holes and attach to unit with two screws removed in step 2 using a T-25 Torx driver. Tighten screws Two units may be installed side-by-side. fully. Cutout width for a side-by-side installation is the cutout 4.
- Page 9 Installation Operation and Maintenance Instructions Water Hookup CAUTION PREPARE PLUMBING Do not use any plastic water supply line. The line is under The water valve uses a standard 1/4" (6.35 mm) compression pressure at all times. Plastic may crack or rupture with age fitting.
-
Page 10: Anti-Tip Bracket
Installation Operation and Maintenance Instructions Anti-Tip Bracket 3. Locate water valve inlet. 1. Slide unit out so screws on top of unit are easily accessible. 2. Remove the two screws from the opposite side of the hinge assembly using a T-25 Torx driver (see below). 4. -
Page 11: General Installation
Installation Operation and Maintenance Instructions General Installation INSTALLATION 1. Plug in the power/electrical cord. LEVELING INFORMATION 1. Use a level to confirm 2. Gently push the unit into position. Be careful not to entangle the unit is level. Level the cord or water and drain lines. should be placed along top edge and side edge as shown. -
Page 12: Overlay Door Panel Dimensions
Installation Operation and Maintenance Instructions Overlay Door Panel Dimensions - ML15CRP1XP OVERLAY PANEL Overlay Panel Dimensions NOTICE Due to differences in surrounding cabinetry the panel may not perfectly align with door. The procedure below is BACK SURFACE MUST HAVE AMPLE FLAT SURFACE designed to provide a finished overlay panel that TO MOUNT OVERLAY PANEL FLAT AND WITHOUT INTERFERENCE... -
Page 13: Overlay Door Panel Installation
Secure overlay panel to door using clamps. A Clamp robust tape may also be 2. Starting at corner, pull gasket used. AGA Marvel away from door. recommends the use of bar clamps to secure the 3. Continue to pull gasket free panel to the door. -
Page 14: Grille Installation
Installation Operation and Maintenance Instructions Door Swing Door Swing 11. Remove clamps from door. NOTICE Wall Wall If panel requires additional adjustment after removing 1/4" Min. 2-1/8" Min. clamps, slightly loosen each screw and adjust panel as (6 mm) (54 mm) necessary. -
Page 15: Door Adjust
Installation Operation and Maintenance Instructions Door Adjust Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. HINGE COVER Hinge cover included with the literature bag is optional. The hinge hardware will be removed and reinstalled on the opposite side of the cabinet. - Page 16 Installation Operation and Maintenance Instructions Install top hinge and door: 1. Install the top hinge. Do not tighten. Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be reused. 2. Rotate the door 180 to reverse and set the door onto the bottom hinge.
- Page 17 Installation Operation and Maintenance Instructions TO REVERSE THE DOOR (Overlay Model) Remove bottom hinge: 1. Remove bottom hinge from cabinet. 2. Remove corresponding screws on opposite side of cabinet. On some models there may be a nut behind one or both screws on either side.
-
Page 18: First Use
NOTICE If not intending to use the ice maker, turn the water supply AGA Marvel recommends discarding the ice produced valve off. It is also important to raise the bin arm of the ice during the first two to three hours of operation to avoid maker (see above). -
Page 19: Airflow And Product Loading
Installation Operation and Maintenance Instructions ICE MAKER ADJUSTMENT 4. Install the ice maker assembly cover. Ice Cube Thickness Adjustment Interval - As Required ADJUSTING ICE HARVEST On ice maker equipped models, adjust the cube size by 1. Remove the front grille (see GRILLE INSTALLATION). changing water amount injected into the ice maker assembly as follows: 2. -
Page 20: Cleaning
Installation Operation and Maintenance Instructions Cleaning Using abrasive pads such as ScotchBrite™ will cause the graining in the stainless steel to become blurred. EXTERIOR CLEANING Vinyl Clad (Black or White) Models Rust not cleaned up promptly can penetrate the surface of Clean surfaces with a mild detergent and warm water solution. -
Page 21: Cleaning Condenser
Installation Operation and Maintenance Instructions DEFROSTING Cleaning Condenser Manual Defrost Models INTERVAL - EVERY SIX MONTHS Unit is a manual defrost model and will require occasional To maintain operational efficiency, keep the front grille free of defrosting. When there is build-up of 1/4" (6 mm) or more of dust and lint, and clean the condenser when necessary. -
Page 22: Extended Non-Use
Extended Non-Use VACATION/HOLIDAY, PROLONGED SHUTDOWN For questions regarding extended non-use, please call AGA Marvel at 800.223.3900. The following steps are recommended for periods of extended non-use or if the unit will be exposed to temperatures of 40°F (5°C) or less: CAUTION 1. -
Page 23: Troubleshooting
Installation Operation and Maintenance Instructions Troubleshooting BEFORE CALLING FOR SERVICE TROUBLESHOOTING GUIDE If you think your AGA Marvel product is malfunctioning, read DANGER the CONTROL OPERATION section to clearly understand the function of the control. ELECTROCUTION HAZARD. Never attempt to repair or... - Page 24 In no event shall AGA MARVEL be liable for connecting tubing and the evaporator that are proven to be any consequential or incidental damages or expenses resulting...
-
Page 25: Obtaining Service
Obtaining Service If Service is Required: • If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. - Page 26 www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 10/11/18 30603 Rev_A...
Need help?
Do you have a question about the ML15CRS1XS and is the answer not in the manual?
Questions and answers