Ice machine operation............Using your freezer ..............CAUTION- Hazards or unsafe practices which could result in Dimensions For 15CM Solid Door........... personal injury or property or product damage. Recommended Rough in Opening Dimensions For 15CM Solid Door............Dimensions For 25CM Solid Door........
UNPACKING YOUR ICE MACHINE OR FREEZER Warranty Registration Remove Packaging It is important you send in your warranty registration card im- Your ice machine has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut mediately after taking delivery of your ice machine or you can the banding material at the bottom of the carton, unfold the register online at www.agamarvel.com.
INSTALLING YOUR ICE MACHINE OR FREEZER Select Location Leveling Legs The proper location will ensure peak performance of your ap- Adjustable legs at the front and rear corners of the unit should pliance. We recommend a location where the unit will be out be set so the unit is firmly positioned on the floor and level from of direct sunlight and away from heat sources.
HANDLE INSTALLATION Handle Installation (Solid Door Models) 1. Remove the handle, (2) screws, and 5/32” allen wrench from the bag shipped inside the cabinet. 2. Locate handle opposite the hinges and secure in place using the (2) screws and the allen wrench. (See Figure 4). •...
DOOR ALIGNMENT Door Alignment Procedure The door should be parallel to the sides and top of the refrig- erator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets on the top and bottom of the door and adjusting the door side to side.
INSTALLING THE ICE MACHINE WATER SUPPLY Water Supply NOTE Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 7) to the water valve inlet on the back of the ice machine (See Figure 6). Be sure the rubber washer is in place in the inlet valve nut.
USING YOUR ICE MACHINE Turning on the ice machine Ice maker operation After connecting the water supply, and setting your ice machine • Make certain water pressure is at least 20 psi and no more in place plug the power cord into the wall receptacle. Then than 120 psi and the water is turned on.
USING YOUR FREEZER Turning on the freezer After setting the freezer in place, leveling (see page 4), plug the power cord into the wall receptacle. The freezer should start after plugging in. The temperature control is factory preset to a mid range setting.
(10.01 to 12.54cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS,15CM SOLID DOOR Electrical Requirements: A 115 volt, 15 amp dedicated circuit is required. A 3 prong grounded receptacle is required. Power outlet can be located in the back wall behind unit. Add 1”...
DIMENSIONS FOR MODEL 25CM SOLID DOOR 35-9/16” (90.32cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 21-25/32” (55.32cm) 33-3/4” to 34-3/4” (85.7 to 88.3cm) 3” to 4” 19-11/16” (7.62 to 10.2cm) (50.09cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, 25CM SOLID DOOR Electrical Requirements: A 115 volt, 15 amp dedicated circuit is required.
DIMENSIONS FOR MODEL 15CAF SOLID DOOR 35-11/16” (90.32cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 24-1/8” to 25-1/8” (61.26 to 63.82cm) 19-11/16” 3-15/16” to 4-15/16” (50.01cm) (10.01 to 12.54cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, 15CAF SOLID DOOR Electrical Requirements: A 115 volt, 15 amp dedicated circuit isrequired.
2. Install product out of direct sunlight. 15CM Features 3. Assure the toe grille vents at front of unit beneath door is Can be installed on the counter top or built in.
CARE AND CLEANING Condenser Air Flow Defrosting Instructions 15CM and 25CM The condenser underneath the cabinet does not re- 1. Push the rocker switch located in the front grille to the quire frequent cleaning; however, satisfactory cooling de- “OFF” position.
TROUBLESHOOTING YOUR ICE MACHINE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting Electrocution Hazard - Never attempt to repair or perform main- guide below. Locate the problem in the guide and refer to the tenance on the unit until the main electrical power has been cause and its remedy before calling for service.
TROUBLESHOOTING YOUR ICE MACHINE OR FREEZER Problem Possible Cause Remedy Unit too warm or too cold inside. • Control set too warm or cold. • Adjust temperature colder or warmer as required. Allow 24 hours for tem- perature to stabilize. •...
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. •...
AGA MARVEL shall issue a credit to the buyer ed by AGA MARVEL and are in lieu of all warranties, express, for all or part of the purchase price, as AGA MARVEL shall de- implied, statutory or otherwise. In particular, AGA MARVEL termine.
Page 20
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41011870-EN Rev J All specifications and product designs subject to change without notice. Such revisions do not entitle the 4/23/12 buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.