Panasonic AW-UE150WP Operating Instructions Manual page 93

Web screen configurations (continued)
Image capture size
Select the resolution for H.264 images.
Selectable options will vary depending on the selected resolution
setting.
Setting value:
H264(1) 1920×1080
1280×720
H264(2) 1920×1080
1280×720
640×360
320×180
160×90
H264(3) 1280×720
640×360
320×180
160×90
H264(4) 1280×720
640×360
320×180
160×90
Factory settings:
H.264(1): 1920×1080
H.264(2): 640×360
Transmission priority
Set the transmission mode for H.264 images.
Setting value:
Constant bit rate Transmits H.264 images at the bit rate specified
in [Max bit rate (per client)].
Frame rate Transmit H.264 images at the frame rate specified
in [Frame rate].
Best effort Transmit H.264 images at a variable bit rate
between the maximum and minimum specified
in [Max bit rate (per client)], according to the
network bandwidth.
Advanced VBR Transmit H.264 images at the frame rate specified
in [Frame rate]. Images will be transmitted so
that the average transmission volume during the
duration specified in [Control time period] will be
the bit rate specified in [Max bit rate (per client)].
Factory settings: Frame rate
<NOTE>
• When [Transmission priority] is set to [Frame rate] or [Advanced
VBR], the number of users that can connect may decrease.
Frame rate
Set the frame rate for H.264 images.
Setting value:
For 59.94Hz:
5fps 1 /15fps 1 /30fps 1 /60fps
* * *
For 50Hz:
5fps 1 /12.5fps 1 /25fps 1 /50fps
* * *
Factory settings:
For 59.94Hz: 30fps
For 50Hz: 25fps
* 1
The [Frame rate] is limited by the [Max bit rate (per client)]
setting. The actual frame rate may be lower than the specified
value.
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Frame rate] or [Advanced VBR].
• [H.264(1)] is fixed at [60fps] (for 59.94Hz) and [50fps] (for 50Hz).
[60fps] (for 59.94Hz) and [50fps] (for 50Hz) cannot be selected for
[H.264(2)] to [H.264(4)].
1
*
1
*
Burst tolerance level
Select how much more than the [Max bit rate (per client)] value to
allow for the H.264 bit rate.
Setting value:
High/Middle/Low
Factory settings: Low
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Advanced VBR].
Control time period
Select the duration for which the H.264 bit rate will be controlled.
Images will be transmitted so that the average transmission volume
during the duration specified will be the bit rate specified in [Max bit
rate (per client)].
Setting value:
1h 1 hour
6h 6 hours
24h 1 day (24 hours)
1 week 1 week
Factory settings: 24h
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Advanced VBR].
Max bit rate (per client)
Specify the H.264 bit rate per client.
When [Transmission priority] is set to [Best effort], specify the
maximum and minimum bit rate.
Setting value:
64kbps/128kbps 2 /256kbps
*
1024kbps /1536kbps
2
*
6144kbps 2 /8192kbps
*
16384kbps /20480kbps
2
*
Factory settings:
H.264(1): 10240kbps
H.264(2): 10240kbps
The range of H.264 bit rates that can be specified varies depending
on the resolution.
• 160 × 90: 64kbps to 2048kbps
• 320 × 180, 640 × 360: 64kbps to 4096kbps
• 1280 × 720: 256kbps to 8192kbps
• 1920 × 1080: 512kbps to 14336kbps
• 1920 × 1080 (60fps), 1280 × 720 (60fps): 1024kbps to 24576kbps
* 2
The H.264 bit rate is limited by the [Bandwidth control (bit rate)]
(→ page 111) setting under the [Network] tab of the network
setup screen [Network]. The actual bit rate may be lower than the
specified value.
Image quality
Select the image quality for H.264 images.
Setting value:
Low(Motion priority)/Normal/Fine(Image quality priority)
Factory settings: Normal
<NOTE>
• This setting is only enabled when [Transmission priority]
(→ page 93) is set to [Constant bit rate] or [Best effort].
93
2 /384kbps 2 /512kbps 2 /768kbps
* * *
/2048kbps /3072kbps /4096kbps
2 2 2
* * *
2 /10240kbps 2 /12288kbps 2 /14336kbps
* * *
/ 24576kbps
2 2
* *
2 /
*
/
2
*
2 /
*