Panasonic AW-UE150WP Operating Instructions Manual page 114

Web screen configurations (continued)
Auto port forwarding
Whether to use the router's port forwarding function is set by selecting
[On] or [Off].
To use the automatic port forwarding function, the used router must
support UPnP and the UPnP function must be enabled.
Setting value:
On Uses the router's port forwarding function.
Off The router's port forwarding function is not used.
Factory settings: Off
<NOTE>
• The port number may be changed by automatic port forwarding. If
the number is changed, the port No. of the camera registered to the
personal computer or recorder must be changed.
• The UPnP function may be used when the camera is connected to
the IPv4 network. IPv6 is not supported.
• To confirm that automatic port forwarding is correctly set, click the
[Status] tab in the maintenance screen [Maintenance] to confirm that
the [UPnP] status is set to [Enable]. (→ page 113)
If [Enable] is not displayed, refer to "Cannot access the Internet from
the Camera" in the "Troubleshooting" section. (→ page 135)
Camera short cut
Whether to create a camera short cut in the [Network] folder of your
personal computer is set by selecting [On] or [Off].
Select [On] to create a camera short cut.
To use the camera short cut function, enable the UPnP function in
advance in your personal computer.
Setting value:
Creates a camera short cut in the [Network] folder of your
On
personal computer.
No camera short cut is created in the [Network] folder of
Off
your personal computer.
Factory settings: Off
<NOTE>
• To display a camera short cut in the Windows [Network] folder, the
Windows component must be added. Refer to the information below
to enable UPnP.
Windows 7
[Start]→[Control Panel]→[Network and Internet]→[Network and
Sharing Center]→[Change Advanced Sharing Settings]→select
[Enable Network Discovery] in [Network Discovery]→click [Save
Changes]→Complete
Windows 8
[Start]→Select [All Applications]→[Control Panel]→[Network and
Internet]→[Network and Sharing Center]→[Change Advanced
Sharing Settings]→select [Enable Network Discovery] in [Network
Discovery]→click [Save Changes]→Complete
z HTTPS
„
Using the HTTPS function enables access to the camera to be
encrypted and communication safety to be improved.
See page 116 for more details on the HTTPS setup method.
CRT key generate
A CRT key (SSL encryption key) is generated by HTTPS.
To generate a CRT key, click the [Execute] button to display the [CRT
Key Generate] dialog.
For more details, refer to "Generating a CRT key (SSL encryption
key)" (→ page 117).
Self‑signed Certificate ‑ Generate
A self-signed security certificate is generated by HTTPS. (Self-signed
Certificate)
To generate a self-signed certificate (security certificate), click the
[Execute] button to display the [Self-signed Certificate - Generate]
dialog and perform the operation.
For more details, refer to "Generating a self-signed certificate
(security certificate)" (→ page 117).
Self‑signed Certificate ‑ Information
This displays information relating to the self-signed certificate
(security certificate).
When the [Confirm] button is clicked, the registered content of the
generated self-signed certificate (security certificate) is displayed in
the [Self-signed Certificate - Confirm] dialog.
Click the [Delete] button to delete the generated self-signed certificate
(security certificate).
CA Certificate ‑ Generate Certificate Signing Request
When using a security certificate issued by the Certificate Authority
(CA) as a security certificate for HTTPS, a Certificate Signing Request
(CSR) is generated for application to the Certificate Authority (CA).
To generate a Certificate Signing Request (CSR), click the [Execute]
button to display the [Certificate Signing Request (CSR) Generate]
dialog and perform the operation.
For more details, refer to "Generating a Certificate Signing Request
(CSR)" (→ page 118).
CA Certificate ‑ CA Certificate install
This displays information relating to server certificates (security
certificates) issued by the Certificate Authority (CA), which are to be
or are already installed.
In the [File Open] dialog, which is displayed by clicking the [Browse]
button, select the file of the server certificate (security certificate)
issued by the Certificate Authority (CA) and click the [Execute] button
to install the server certificate (security certificate).
If the server certificate (security certificate) is installed, its file name
will be displayed.
For more details, refer to "Installing a Server Certificate"
(→ page 119).
114