Dynacord DPC 8000 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

DPC 8000

en |

Table of Contents

Summary of Contents for Dynacord DPC 8000

Page 1 DPC 8000 en |...
Page 3: Table Of Contents
DPC 8000 Table of contents | en Table of contents Safety notes Brief description System overview Scope of delivery and warranty Installation Bottom Delivery condition Button labeling Retrofit options 5.5.1 Alarm button (EB DPC) 5.5.2 Key switch (NRS 90231) Activation PCA BUS interface 6.1.1...
Page 4: Safety Notes
| Safety notes DPC 8000 Safety notes Danger! The lightning symbol inside a triangle notifies the user of high-voltage, uninsulated lines and contacts inside the devices that could result in fatal electrocution if touched. Warning! An exclamation mark inside a triangle refers the user to important operating and service in- structions in the documentation for the equipment.
Page 5 DPC 8000 Safety notes | en 14. Please ensure that no dripping water or spray can penetrate the inside of the device. Do not place any objects filled with fluids, such as vases or drinking vessels, on top of the device.
Page 6: Brief Description
| Brief description DPC 8000 Brief description The DPC 8015 is a call station for the PROMATRIX 8000 system. As standard, the call station has a goose neck microphone with pop shield and permanent monitoring, a total of 20 buttons, an illuminated LC display, and an integrated loudspeaker.
Page 7: System Overview
DPC 8000 System overview | en System overview The PROMATRIX 8000 system includes the DPC 8015 call station and the DPC 8120 call station extension. The call station is equipped with a goose neck microphone, and has 15 customizable selection and function buttons and five pre-programmed menu/function buttons.
Page 8: Scope Of Delivery And Warranty
6-pin connecting cable for call station extension Connecting holder for call station extension Connecting plate for call station extension Screws (self-tapping) Technical information Warranty card with safety notes Table 4.2: DPC 8120 scope of delivery Warranty For information regarding the warranty, see www.dynacord.com 28-Feb-2013 | |...
Page 9: Installation
DPC 8000 Installation | en Installation Figure 5.1: DPC 8015 28-Feb-2013 | |...
Page 10 | Installation DPC 8000 Figure 5.2: DPC 8120 Number Element Description Selection buttons Circuit and group selection buttons with green and yellow LED. Button installation For up to three optional alarm buttons or key slots switches POWER LED Illuminates green if the power supply is on...
Page 11: Bottom
DPC 8000 Installation | en Bottom Figure 5.3: DPC 8015 28-Feb-2013 | |...
Page 12: Delivery Condition
| Installation DPC 8000 Figure 5.4: DPC 8120 Number Element Description EXT interface Connection for DPC 8120 call station extension PCA BUS interface Connection to PROMATRIX 8000 CONTROLLER LINE/PTT interface Connection for external audio devices or a PTT button...
Page 13: Button Labeling
5.5.1 Alarm button (EB DPC) The EB DPC is an optional button for installation in the DPC 8000 series call stations. The transparent cover cap prevents unintentional actuation of the button. A high-efficiency LED is integrated for optical visualization, while also ensuring maximum operational reliability. The button feed lines are monitored by the call station.
Page 14: Key Switch (Nrs 90231)
5.5.2 Key switch (NRS 90231) The NRS 90231 is an optional key switch for installation in the DPC 8000 series call stations. The key switch feed lines are monitored by the control station. If an error occurs, this is indicated in the error log of the PROMATRIX 8000 system.
Page 15 DPC 8000 Installation | en Figure 5.6: NRS 90231 Assembly Note the following information regarding installation of the NRS 90231 in the DPC 8015 call station. Disconnect the call station from all connectors Unscrew the call station baseplate (4 screws)
Page 16: Activation
| Activation DPC 8000 Activation PCA BUS interface Notice! If the call station is connected to a DPM 8016 via the PCA BUS, the call station is automatical- ly configured depending on the set CAN address. The call station is ready to use after a few seconds.
Page 17: Line Interface
DPC 8000 Activation | en Figure 6.3: Assignment of the PCA bus connector LINE interface Usage as audio input The LINE interface allows an external audio device (e.g. CD player) to be connected. If configured in IRIS-Net, the audio source connected to this interface can be used for a program in the PROMATRIX 8000 system.
Page 18: Ext Interface
| Activation DPC 8000 EXT interface This socket is primarily used to connect a DPC 8120 call station extension. To do so, connect the DPC 8120 to the EXT socket of the call station via the connecting cable provided.
Page 19: Configuration
DPC 8000 Configuration | en Configuration The call stations of a PROMATRIX 8000 system should be configured on the control panel via a PC using IRIS-Net as this is the simplest method, and there are no restrictions. Only limited programming is possible on the actual call stations themselves. To configure the call station via the LC display, the call station must be switched to menu mode as described below.
Page 20 | Configuration DPC 8000 Operation mode PROGRAM 1 - 4 +¯ Program 1 Volume 1 Program assignment Program 4 Pre-Gong Volume 4 Buzzer SETUP Date / Time CAN address LCD contrast CAN baudrate CAN termination LCD brightness Firmware version LED test Monitor Vol.
Page 21: User Menu
DPC 8000 Configuration | en User menu Program selection The call station allows programs to be assigned to individual circuits or groups of the PROMATRIX 8000 system. Program transfer has the lowest priority. With single-program technology, the music must be muted or switched off in all circuits for the duration of an announcement.
Page 22: Setup Menu
| Configuration DPC 8000 Buzzer The built-in loudspeaker can be programmed as an acoustic warning signal. The signal tone sounds in the event of incorrect operation or malfunction, or as a warning. Pressing the ↵ button takes the user to the Buzzer submenu. The current setting of the buzzer ("on" or "off") is displayed.
Page 23 DPC 8000 Configuration | en CAN address Pressing the ↵ button takes the user to the CAN Address dialog box. Pressing the ↑ or ↓ button sets the required CAN address. The call station can be assigned a CAN address between 1 and 16.
Page 24: Operation
| Operation DPC 8000 Operation Indicators The meanings of the call station LED indicators are summarized below. Standard configuration of the call station is assumed. Status Description Zone (green) Circuit or group not selected Illuminated green • Circuit or group selected •...
Page 25: Functions
DPC 8000 Operation | en Status Description Green, flashing quickly • At least one of the selected circuits is occupied with higher priority (announcement, gong, alarm) and cannot be interrupted • A call that has already started will be interrupted by the higher priority...
Page 26 | Operation DPC 8000 Button Announcement mode Menu mode ↑ This button switches the system on and off. The This button is used to scroll activation process may take a few seconds. As up when navigating through soon as the system is ready for operation, the the menu.
Page 27 DPC 8000 Operation | en Button Announcement mode Menu mode Selection There are 15 selection buttons with Entering numbers buttons corresponding LEDs. These are used to select individual circuits or groups for announcements, gong/alarm signals, speech reproduction, or program assignment (press once = on, press again = off).
Page 28 | Operation DPC 8000 Notice! The alarm trigger depends on the priority of the call station from which the alarm is activated. The user can configure the call stations from which an alarm may be triggered. If configured, an alarm can also be triggered if the system is in standby mode. A visual and possibly also acoustic signal is sent to each call station in the system to indicate that an alarm is active.
Page 29: Maintenance
DPC 8000 Maintenance | en Maintenance The DPC 8000 does not require any maintenance. 28-Feb-2013 | |...
Page 30: Technical Data
| Technical data DPC 8000 Technical data DPC 8015 Supply voltage 15–58 V DC Maximum supply current (without < 80 mA / 24 V EXTENSIONS) < 110 mA / 18 V Maximum supply current (with 5 DPC 8120 < 180 mA / 24 V EXTENSIONS) <...
Page 31: Block Diagram
DPC 8000 Technical data | en Product dimensions (Width by Height by 140 by 167 by 65 mm Depth) Net weight 0.35 kg 10.1 Block diagram 28-Feb-2013 | |...
Page 32: Dimensions
| Technical data DPC 8000 10.2 Dimensions Figure 10.1: DPC 8015 Figure 10.2: DPC 8120 10.3 Standards The DPC 8000 CALL STATION meets the following standards (version: October 2012): • EN 54-16 28-Feb-2013 | |...
Page 33 DPC 8000 Technical data | en • EN 55103-1 • EN 55103-2 • EN 60945 • • ICES 003 28-Feb-2013 | |...
Page 34: Appendix
| Appendix DPC 8000 Appendix 11.1 CAN bus basics The CAN bus uses a bus or line topology as its network topology. This means that all participants are connected to a single twisted pair cable (shielded or unshielded), where the cabling must run from one bus participant to the next.
Page 35 DPC 8000 Appendix | en Figure 11.2: DPC 8120 Assembly See the following information regarding installation of call station extension DPC 8120 on call station DPC 8015. Disconnect the call station from all connectors Align the call station and call station extension next to each other with the top sides...
Page 36 | Appendix DPC 8000 Notice! If a call station extension is replaced in a call station system that has already been configured, the replacement device must be assigned the address of the first device via the DIP switch EXTENSION ADDRESS.

Dynacord DPC 8000 Manual

Quick Links

Related Manuals for Dynacord DPC 8000

Summary of Contents for Dynacord DPC 8000

Table of Contents