1. Manuals
  2. Brands
  3. Yangzhou Shenzhou Wind-driven Generator Manuals
  4. Inverter
  5. FD2.1-200-8L
  6. User manual

Yangzhou Shenzhou Wind-driven Generator FD2.1-200-8L User Manual

Wind generator up to 20000w
Hide thumbs
Table of Contents

Advertisement

Quick Links

Yangzhou Shenzhou Wind-driven Generator Co.,Ltd
USER ' S MANUAL
(2007-04-13)

Advertisement

Table of Contents
loading

Summary of Contents for Yangzhou Shenzhou Wind-driven Generator FD2.1-200-8L

  • Page 1 Yangzhou Shenzhou Wind-driven Generator Co.,Ltd USER ’ S MANUAL (2007-04-13)

  • Page 2: Table Of Contents

    CONTENTS Model & Parameter List ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 3 ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 5 Installation Specification of Guyed Tower ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 13 Installation Specification of Tapered Tower ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 15 Configuration Specification of Batteries Electric Wiring ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 16 ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 17 Maintenance ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 17 FAQS ┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅┅ 19 Annex one: Off-grid Electric Wiring Annex Two: Controller Specification （...

  • Page 3: Model & Parameter List

    Model & Parameter List Model FD2.1-200-8L FD2.1-200-8H FD2.5-300-8L FD2.5-300-8H Rated power(W) 200W 300W 300W Rated voltage (V) Rotor diameter(M) Start-up wind speed(m/s) Rated wind speed （ m/s ） Security wind speed(m/s) Rated rotating rate （ r/m ） Blade material glass fiber...
  • Page 4 Model FD6.4-5000-16L FD6.4-5000-16H FD8.0-10K-20L FD8.0-10K-20H Rated power(W) 5000W 10000W Rated voltage (V) Rotor diameter(M) Start-up wind speed(m/s) Rated wind speed （ m/s ） Security wind speed(m/s) Rated rotating rate （ r/m ） Blade material glass fiber glass fiber glass fiber glass fiber Blade quantity Model...

  • Page 5: Installation Specification Of Guyed Tower

    Installation Specification of Guyed Tower Step 1: Choosing Installation Sites The wind turbine should be erected high and far away from obstacles as possible in order to get relatively high wind speed. Meanwhile soil quality of installation location should be taken into consideration.
  • Page 6 Special attention should be paid to the following when laying out the base and anchor: 1. Connecting line of two side anchors should be in parallel with the connection of two pinholes on the tail edge. 2. Make sure the side of tail edge with screw thread face the anchor. 3.
  • Page 7 Graph 2 3. Annular anchors need to be deposited 60 ° to 80 ° along the base direction and check the distance between the four hooks of the anchors and the center of the base. Four anchors should be horizontal (as shown in the graph 3). Graph 3...
  • Page 8 Step 4 Assembly of the tower and wind turbine 1. First, insert the main section of tower into base, then insert the axis pin into base and insert the split pin. (As shown in the graph 4) Graph 4 2. Connect each section of tower one by one, place the tower on the supporting stand after assembly.
  • Page 9 Graph 5 Make sure: L1=L2=L3 (error allowed: ± 5mm) Utilizing spanner for force moment when screwing blades ’ bolts and achieving the set force moment （ 200w 、 300w ： 15Nm ± 1 ； 500w 、 1kw 、 2kw ： 30Nm ± 1 ； 3kw 、 5kw 、 10kw 、 20kw ： 50Nm ±...
  • Page 10 Graph 6 7. Cover the dome. 8. (For 3kw and above 3kw wind turbine) infix the aviation plug on the generator into the socket of dogvane, and then install the dogvane. Special attention should be paid to the direction of dogvane.
  • Page 11 5. Fix the lower pulley on the front anchor. Fix one side of the longest thin cable wire on the pulley of supporting pole. Make sure the other side drill through the pulley, and then drill through the upper and lower pulley. Finally, fix it on a hoist or tractor (as shown in the graph 7). Graph 7 (For 2kw &...

  • Page 12: Installation Specification Of Tapered Tower

    2. Go on pulling the bracing cord until the tower stands upright. Separate the working cord and fix it on its anchor. 3. Check and adjust the strain of each fixed wire cable. Over tight force may bend the tower while over loose force may cause the tower unstable and shakable.

  • Page 13: Configuration Specification Of Batteries

    Model Code in the 1000W 2000W 3000W 5000W 10KW 20KW graph 8 Ground depth(m) ( D1) Ground diameter(m) ( C1) Burial depth of cotter bolt (m) ( D2) Layout diameter of cotter bolt ( C2) 1000 1200 (mm) Specification of cotter bolt ( T) Quantity of cotter bolt ( N)

  • Page 14: Electric Wiring

    4. Suggested battery capacity for various model (as shown in the table 3) Model 200W 300W 500W 1000W 2000W 3000W 5000W 10KW 20KW Voltage of single battery (V) Capacity of single battery(AH) Quantity in series Table 3 5. Charged parameter of batteries (as shown in the table 4) Battery voltage(V) Float charge voltage ( V) Overvoltage ( V)

  • Page 15: Maintenance

    classified as positive electrode and negative one. All should be connected to the connecting poles at the back of controller accordingly. b. The anemoscope should be installed on house roof or open areas, and must be vertical against the ground. One end of the matched cable of anemoscope should be inserted into the socket under the anemoscope with the other end inserted into the socket accordingly.

  • Page 16: Faqs

    FAQS ○ Why does not my electro-equipment work after connected to inverter? ● Check the dump energy. If the energy is not enough, the system will not operate normally; if the energy is enough, please check the connecting wire between batteries and inverter is correct.
  • Page 17 (For 2KW & above 2KW) 1. Disconnect the generator and controller. Make the three output lines be short circuit to prevent the blades from further running. 2. Do the reverse steps of installation to put down the generator. ○ Can I enlarge the batteries' capability to extend the available time for electrical appliance? ●...
  • Page 18 ● It ’ s 15 years under normal care. If you have more questions, please contact us by phone or E-mail. * The color of photographs may be different from real objects. * No notification if the manual modified. *The guarantee of turbine and controller is 2 years, and the inverter is 6months from the date of purchasing (non-done by man or majeure)

  • Page 19: Annex One: Off-Grid Electric Wiring

    Annex 1: Off-grid electric wiring...

  • Page 20: Annex Two: Controller Specification （ 3Kw & Above 3Kw

    Annex Two: Controller Specification （ 3kw & above 3kw ） 1. Under initial state, controlling board will indicate “ auto ” and “ turn-on ” . When the wind speed reaches or surpasses 2m/s under this state, wind turbine will trace wind direction automatically.
  • Page 21 Furl 60 degree 15m/s 15m/s 15m/s 16m/s Furl 90 degree （ shutdown ） 18m/s 18m/s 18m/s 20m/s Table 5 6. The system will continually check battery voltage under normal operation state. When over or under voltage, the system will alarm automatically and send out the shutdown order. Note: anemoscope should be installed on the wind turbine system of 3KW and above 3KW, otherwise the system will not be operated normally.

  • Page 22: Annex Three: Specification Of Wind-Speed Monitor

    Annex Three: Specification of wind-speed monitor (FS01) The function of wind speed scope is to indicate the real time wind speed and wind scale, together with alarming when the wind is weak or strong. It consists of wind speed sensor (FS10), wind speed scope (FS100) and connecting wire.
  • Page 23 Picture 10 Wind speed sensor (FS10) (Picture 11) Picture 11 Structural features (Picture 12)
  • Page 24 风 速 仪 Wind Speed : 08.4m/s 5 level 工作 过风速 欠风速 功能 数字 移位 Diagram 12 Specification of each part 1) Anemoscope board 2 ） Liquid crystal: turn-on, the background light is on. (It will shut down automatically after 5 second if there is no operation.) Wind speed figure is displayed, such as 8.4m/s.
  • Page 25 among different figures; combined with figure key, you can set the requisite Wmin, Wmax and the return difference. 2 Parameter setting: a. Press the function key, and you will enter into the setting menu of Wmin and Wmax (as shown in the diagram 13).
  • Page 26 Wind Speed: Hight 16.5m/s 7 level Diagram 15 Note: “ wind speed High ” means the wind speed is too high. “ 16.5m/s ” means wind speed is 16.5m/s. “ 7 level ” means wind scale is 7. 2 ） Under wind speed alarming (wind speed W ≤ Wmin): e.g.: (diagram 16): background light is on, alarming;...

  • Page 27: Annex Four: Specification Of Analyzing System For Wind-Speed Gathering

    Annex Four: Specification of Analyzing System for Wind-speed Gathering (FS02) The system of measuring wind consists of wind-speed sensor (FS10), dogvane (FS20), data collector (FS200) and matched cable. Usually, data collector (FS200) can display the information of wind speed, wind direction and set the parameter. Meanwhile, following is going to show you the procedure of connecting the wind-measuring system and computer.
  • Page 28 Installation & Connection 1. Wind-speed sensor installation Install the wind-speed sensor on the supporting frame. If there is wind available, the three cups of wind-speed sensor will run. 2. Connection of FS200 and wind-speed sensor Insert the aviation plug of wind-speed sensor ’ signal line into the aviation socket of FS200. 3.
  • Page 29 Picture 17 Note: Illumination: the four direction key control the move of cursor, press ”→” to enter the menu option, press “←” to return to the up menu, press ” + ” ( “ - ” ) to increase( decrease) the parameter.
  • Page 30 system time. Record interval (Picture 20) Picture 20 It is used to set interval of the history data, 1min~60min adjustable. Supposed that it is set 2minute, and then the time of PH3000 can record is: 8000/30min/24 hours = 11 days Alarm set (Picture 21) Picture 21 When wind speed exceeds the upper limit, relay is closed then alarm.
  • Page 31 Picture 22 It is used when communication with computer. It correspond to the weather station ID of the computer software. After right set, the PH3000 can work persistently. Connection of FS200 and computer Connect the RS232 serial of FS200 to the RS200 serial of computer and have the FS2000 computer software run.
  • Page 32 Diagram 23 Choosing weather station System default the weather station 10, which is consistent with the address of wind-speed dogvane. Open serial Choose the serial, and set the communicating baud rate on 9600bps, and then open the serial. Read the setting data Click the button of downloading the present setting to read data of the present wind speed and wind direction.
  • Page 33 Download the history data Read the history data of anemoscope by clicking the button of reading history data. The history data are saved in the database of Microsoft Access. Users can observe and analyze history data of wind speed by table or curve view. Setting system parameter (Diagram 24) Diagram 24 Serve as reading or setting the system parameter of anemoscope.
  • Page 34 Diagram 25 Curve view (Diagram 26) First of all, choose the date scope of historical record you need to check, and then click the curve view. The curve diagram of history record will be shown. There are two types of displays, namely, overall display and partial display.
  • Page 35 Rose diagram of wind can illustrate the distribution and scope of different wind direction all the year round. Diagram 27...

This manual is also suitable for:

Fd2.5-300-8lFd2.5-300-8hFd2.1-200-8hFd2.7-500-10lFd2.7-500-10hFd3.0-1000-10h ... Show all

Table of Contents