Page 1
Carefully check the device parts list before using. For any doubt, contact Launch distributor immediately. Due to the product upgrade, tiny difference between the user manual and the device will not be further noticed. Take the device as standard.
Page 2
LAUNCH BST-460 Battery System Tester User Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference...
Page 3
LAUNCH is not responsible for any use of this information as applied to other units. Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs, or expenses incurred by purchaser or...
BST-460 Battery System Tester User Manual Chapter 1 Product Summary 1.1 Product Profile BST-460 Battery Tester adopts the state-of-the-art conductance testing technology in the world to easily, quickly and accurately measure the actual cold cranking amps capability of the vehicle starting battery, healthy state of...
LAUNCH BST-460 Battery System Tester User Manual Cranking test is used to test and analyze the starting motor. Testing the actual required cranking current and cranking voltage of the starting motor is helpful to determine whether the starting motor works properly or not. If the starting motor runs improperly, find the possible reasons: lubricating system malfunction may cause an increased starting loaded torque;...
LAUNCH BST-460 Battery System Tester User Manual 2. Voltage Measurement Range: 8-30VDC 1.4 Working Environment Requirement Working Environment Temp.: -20° C-55° C/-4° F-131° F It is applicable for automotive manufacturers, automotive maintenance and repair workshops, automotive battery factories, automotive battery distributors,...
LAUNCH BST-460 Battery System Tester User Manual Chapter 2 Tester Structure BST-460 mainly consists of battery tester main unit and testing cables. BST-460 Battery Tester main unit cover is made of ABS acid-resistant plastic. Removable testing cables...
LAUNCH BST-460 Battery System Tester User Manual Chapter 3 Operation 3.1 Pre-Test 3.1.1 Connect Tester Before test, clean battery poles with metal wire brush and alkaline detergent to avoid the tolerance caused by oil and dust to the test result.
Enter additional function program via MENU key. 3.2 Tester Startup The tester automatically starts up after the clamps are correctly connected, and displays the Launch startup interf ace (Default voltmeter is ON) refer to figure 1. Figure 1, Startup Interface with Voltmeter on By default, the voltmeter value at the middle bottom of the startup interface can be used as DC voltmeter.
LAUNCH BST-460 Battery System Tester User Manual Figure 2, Startup Interface with Voltmeter off 3.3 Battery Test After entering battery test program, the tester will display the tester model and version approx. 2 seconds, see figure 3 . Figure 3, Interface with tester model and version The tester will display the following contents in a sequence, select the desired items accordingly.
LAUNCH BST-460 Battery System Tester User Manual Follow the instructions to turn lights on to eliminate battery surface charge, the tester will then display the following messages in a sequence: Now the tester detects the surface charge has been eliminated, turn lights off as prompted, then press OK key.
LAUNCH BST-460 Battery System Tester User Manual way, it ensures a more accurate test result. NOTE: In case of In-Vehicle, select Before Charging for Cold Vehicle and After Charging for Hot Vehicle. 3.3.3 Select Battery Type After the battery charge status is chosen, the tester will enter battery type selection interface: Regular Flooded, AGM Flat Plate, AGM Spiral or Gel battery.
NOTE: For REMOTE test, tolerance may exist. For any doubt, remove the battery and select "OUT-OF-VEHICLE" to re-test. 3.3.4 Battery System Standard and Rating BST-460 battery tester will test each battery according to the selected system and rating. Use UP/DOWN key to select according to the act ual system standard...
Page 15
LAUNCH BST-460 Battery System Tester User Manual in the below picture. CCA: Cold Cranking Amps, specified by SAE&BCI, most frequently used value for starting battery at 0° F ( -18° C). BCI: Battery Council International standard Cranking Amps standard, effective starting current value at 0°...
LAUNCH BST-460 Battery System Tester User Manual 100-2000 100-2000 100-2000 26A17--245H52 100-1400 100-1400 100-2000 100-2000 100-1400 Input correct test standard and rating, pre ss OK key, the tester starts to test and a screen similar to the following figure will appear: It takes around 3 seconds to display the battery test result.
Page 17
LAUNCH BST-460 Battery System Tester User Manual The battery is in good health, please be free to use! NOTE: SOH means State of Health SOC means State of Charge 2) Good, Recharge The battery is good but with low power. Please recharge it before using.
LAUNCH BST-460 Battery System Tester User Manual The battery has internal damage, broken cell or short circuit, please replace it. 5) Charge, Retest Unstable battery shall be recharged and retested to avoid error. If same test result appears after recharge and retest, the battery is regarded as damaged, please replace it.
LAUNCH BST-460 Battery System Tester User Manual NOTE: While the system prompts you to start engine, pressing RETURN key can not exit the current interface. Follow the on-screen instructions to start the engine, the tester will automatically complete the cranking test and display the result.
Page 20
LAUNCH BST-460 Battery System Tester User Manual NOTE: To exit when this prompt message appears on the screen, misfire the engine and press RETURN key after about 50 seconds . Press OK key to start the charging test. NOTE: Do not shut down the engine during the test. All electrical appliance and device are in OFF state.
Page 21
LAUNCH BST-460 Battery System Tester User Manual Operate accordingly to increase the engine rotating speed to above 3000 revolutions, and keep it for 5 seconds. The tester starts the charging volt test after an increased revolution is detected. See below picture: After the test finished, the tester displays the valid charging volts, ripple test result and charging test result.
LAUNCH BST-460 Battery System Tester User Manual problems are detected. 2) Charging Volt: Low Charging volt of the charging system is low. Check whether slip or running off occurs on the generator drive belt. Check the connection between generator and battery is normal or not.
Once finished, it shows "OK" for 2 s econds, then return to the previous interface. 3.7.2 Voltmeter BST-460 Battery Tester can also be used as DC voltmeter. The working range is 8VDC-30VDC. CAUTION: BST-460 Tester may be damaged when connected to...
LAUNCH BST-460 Battery System Tester User Manual This function enables you to set the voltmeter On/Off at the bottom line of the startup interface. If successful, it shows "OK" for 2 seconds, then return to the previous interface. 3.7.3 Screen Light Adjustment...
LAUNCH BST-460 Battery System Tester User Manual Chapter 4 Daily Maintenance 4.1 Troubleshooting 4.1.1 Screen Not Light Check whether the battery is well connected or reverse connection between the positive pole and negative pole exists or not. Check whether the test cable is broken off or dropped down.
Page 26
The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Page 27
Launch website: http://www. cnlaunch.com http://www.x431.com Statement: LAUNCH reserves the rights to make any change to product designs and specifications without notice. The actual object may differ a little from the descriptions in the manual in physical appearance, color and configuration. We...
Need help?
Do you have a question about the BST-460 and is the answer not in the manual?
Questions and answers