Hytera RD106X User Manual
  1. Manuals
  2. Brands
  3. Hytera Manuals
  4. Repeater
  5. RD106X
  6. User manual
Hytera RD106X User Manual

Hytera RD106X User Manual

Digital repeater
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Preface
Welcome to the world of Hytera and thank you for purchasing this product. This manual includes a
description of the functions and step-by-step procedures for use. To avoid bodily injury or property loss
caused by incorrect operation, please carefully read the Safety Information Booklet before use.
This manual is applicable to the following product:
RD106X Digital Repeater (X may represent 2, 5, 6 or 8)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RD106X and is the answer not in the manual?

Questions and answers

Related Manuals for Hytera RD106X

Summary of Contents for Hytera RD106X

  • Page 1 Preface Welcome to the world of Hytera and thank you for purchasing this product. This manual includes a description of the functions and step-by-step procedures for use. To avoid bodily injury or property loss caused by incorrect operation, please carefully read the Safety Information Booklet before use.

  • Page 2: Copyright Information

    Copyright Information Hytera is the trademark or registered trademark of Hytera Communications Corporation Limited (the Company) in PRC and/or other countries or areas. The Company retains the ownership of its trademarks and product names. All other trademarks and/or product names that may be used in this manual are properties of their respective owners.

  • Page 3: Fcc Statement

     United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1091  American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1:2005; Canada RSS102 Issue 5 March 2015  Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to...
  • Page 4 exposure limits in the above standards and guidelines, users should always adhere to the followings:  Gain of antenna must not exceed 10dBi (Outdoor) or 5dBi (Indoor).  Antenna Installation: install the antenna at least 150cm (Outdoor) or 85cm (Indoor) away from your body, in accordance with the requirements of the antenna manufacturer/supplier.

  • Page 5: Eu Regulatory Conformance

    EU Regulatory Conformance As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant provisions of 2014/53/EU. Please note that the above information is applicable to EU countries only.

  • Page 6: Documentation Information

    Documentation Information Icon Conventions Icon Description Indicates references that can further describe the related topics. Indicates situations that could cause data loss or equipment damage. Notational Conventions Item Description Example To save the configuration, click Apply. Denotes menus, tabs, parameter names, window names,...

  • Page 7: Packing List

    1. Packing List Please unpack carefully and check that you have received the following items. If any item is missing or damaged, please contact your dealer. Item Quantity (PCS) Item Quantity (PCS) Repeater Documentation Kit Power Cord  Figures in this manual are for reference only. ...

  • Page 8: Product Overview

    2. Product Overview 2.1 Front Panel Part Name Part Name Air Inlet for PA Timeslot A RX Indicator Channel Up Key Timeslot A TX Indicator Channel Down Key Analog Mode Indicator Seven-segment Display Digital Mode Indicator Alarm Indicator Audio/Programming Connector Timeslot B RX Indicator Air Inlet for Power Supply Timeslot B TX Indicator...

  • Page 9: Internal Parts

    2.3 Internal Parts Part Name Part Name Power Supply Module Wind Scooper Network Board Baseband Module Control Panel PA Module Floating Charge Board...

  • Page 10: Installation Requirements

    3. Installation To ensure optimum performance and reliability of the repeater, install it properly according to the following instructions. 3.1 Installation Requirements Installation Environment The repeater must be installed in a dry and well-ventilated place. The ambient temperature ranges from -30°C to +60°C, and the relative humidity is 95%.

  • Page 11: Post-Installation Check

    1. Wear the anti-static gloves. 2. Place the repeater to a proper location. 3. Connect accessories including the antenna, feed lines, and power cords to the repeater. The antenna and feed lines need to be purchased separately. 4. Ground the repeater through the Ground Screw located on the rear panel. 3.4 Post-installation Check To check whether the repeater works properly, do as follows: Turn the repeater on.

  • Page 12: Basic Operations

    4. Basic Operations 4.1 Turning the Repeater On or Off If the repeater is connected to a DC power supply, press the power switch on the DC power supply to turn the repeater on or off. If the repeater is connected to an AC power supply, press the AC Power Switch located in the rear panel to turn the repeater on or off.

  • Page 13: Alarm Information

    5. Alarm Information With the Alarm feature enabled by your dealer, the repeater can detect alarms. When an error occurs, the display shows the alarm code with the Alarm Indicator on the front panel glowing red. 5.1 Low Forward Power Alarm Description When the forward power is below the preset value, the Alarm Indicator glows red and the display shows the alarm code E8.

  • Page 14: Over Temperature Alarm

    5.3 Over Temperature Alarm Description When the temperature of the PA module exceeds the upper threshold, the Alarm Indicator glows red and the display shows the alarm code E6. Then the repeater will stop transmission. Solution 1. Check whether the temperature of the PA module surface is over 120 C. ...

  • Page 15: Voltage Standing Wave Ratio (Vswr) Alarm

    Solution 1. Use voltmeter to check whether the DC or AC power voltage is too low or too high.  If yes, replace the DC or AC power supply.  If no, proceed with Step 2. 2. Check whether the power cord is loose or damaged. ...

  • Page 16: Troubleshooting

    6. Troubleshooting Analysis Solution Phenomena The power cord may be unconnected or not Properly connect the power cord and securely connected to the outlet. ensure secure connection. Power-on Failure The fuse in the power cord may be Check if the fuse has blown. If yes, damaged.

  • Page 17: Care And Cleaning

    7. Care and Cleaning To guarantee optimum performance as well as a long service life of the product, please follow the tips below. 7.1 Product Care  Keep the product at a place of good ventilation and heat dissipation to facilitate normal work. ...

  • Page 18: Optional Accessories

    8. Optional Accessories Use the accessories specified by the Company only. If not, Hytera shall not be liable for any losses or damages arising out of use of unauthorized accessories. For more information of the main optional accessories for the repeater, please consult your local dealer.

Table of Contents