Page 1
UP-CHCR1 Maker Board User’s Manual 1 Last Updated: February 7, 2018...
Page 2
AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft Windows is a registered trademark of Microsoft Corp. Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation Core, Atom are trademarks of Intel Corporation ...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UP-CHCR1 If any of these items are missing or damaged, please contact your distributor or sales representative immediately. Preface...
Page 5
(if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the AAEON.com for the latest version of this document. Preface...
Page 6
Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
Page 7
If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
Page 8
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 9
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Module This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module.
Page 10
the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 12
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
Specifications System 56.5 mm × 66 mm Form Factor Intel ® Atom™ x5-Z8350 Processor Up to 1.84 GHz CPU Frequency Processor integrated Chipset Onboard DDR3L-1600 Memory Type 4 GB Max Memory Capacity SPI BIOS – 64Mb flash BIOS ...
Page 16
USB 3.0 x 1 16 GB / 32 GB / 64 GB Onboard eMMC 100 PIN Docking Connector Expansion Slot (28 x GPIO, 2 x I2C, 1 x SPI, 1 x HSUART1, 1 x ADC, 5V, GND) USB Device 1 x PCIe 1 x USB2.0...
List of Switches and Connectors Please refer to the table below for all of the board’s jumpers that you can configure for your application Connector Type Reference Function Power Button (TF) Push Button Switch.HCH.PTS-099 RTC Battery (TF) WAFER BOX 2P .180D.1.25mm.CATCH.1201-700-02S Wafer MIPI DSI (TF)FPC/FFC...
2.3.1 Power Button (SW1) Position Function SW1 1 (default) SW1 0 Power ON 2.3.2 RTC Battery Wafer (CN1) Signal +V_COIN_BAT Chapter 2 – Hardware Information...
2.3.9 DC Jack (CN30) Signal 2.3.10 Update BIOS Header (CN38) Signal Signal 3.3V FST_SPI_CS0_N FST_SPI_CLK FST_SPI_D1 FST_SPI_D0 SPI_SOCK_HOLD_N Chapter 2 – Hardware Information...
Driver Download and Installation *Please access https://up-community.org and go to the Downloads section to find the relevant driver. Chapter 3 – Drivers Installation...