Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for sauter TD GOLD 40
Summary of Contents for sauter TD GOLD 40
- Page 1 Sauter GmbH Ziegelei 1 Tel: +49-[0]7433- 9933-199 D-72336 Balingen Fax: +49-[0]7433-9933-149 E-Mail: info@sauter.eu Internet: www.sauter.eu Instruction Manual Goldtester SAUTER TD GOLD 40 Version 1.3 05/2018 PROFESSIONAL MEASURING TD_GOLD_40-BA-e-1813...
-
Page 2: Table Of Contents
Takeover of sound velocity to the instrument ..........6 Measurement with the TD special gold ............6 Interpretation of the measured value ............6 Alternative measurement procedures ............7 Instruction Manual of TD-US as a base for using TD GOLD 40 ....7 12.1 Features ............................. 7 12.2 Specifications ........................... -
Page 3: Main Function Of The Kern Ssg Software For Gold Tester
Text of the Instruction Manual in HELP Menu Main function of the KERN SSG Software for Gold Tester With this software, the individual ultra sound velocity of your gold piece can be calcu- lated. Gold pieces as bars or coins are typically not made of pure gold with a sound velocity of 3240 meter per seconds (m/s). -
Page 4: Choice Of The Outer Appearance
Choice of the outer appearance Selection between gold bar and gold coin Weight and Dimensions Fill in the weight and the dimensions of the piece of gold (test object) The following procedure for the measurements is recommended: Determination of the weight: Type approved balance, e.g. KERN KB 650-2NM * Turn the balance on * Warm up for approx. -
Page 5: Safety Level
Safety level Every measurement has its tolerance. A typical tolerance of e.g. 5% of the measured value represents a safety level of 95%. This tolerance is the value by which the measured value may vary from the real or true value. As in this procedure, two measured values are compared with each other, it is recommended to use a broad tolerance. -
Page 6: Takeover Of Sound Velocity To The Instrument
After adding all components, the software shows the exact and individual sound ve- locity of the test object. This individual sound velocity is to be set into the SAUTER TD Ultrasound instru- ment. 8 Takeover of sound velocity to the instrument Please turn the instrument on. -
Page 7: Alternative Measurement Procedures
“Laboratory balances” attractive instruments and solutions. 12 Instruction Manual of TD-US as a base for using TD GOLD 40 12.1 Features * The exclusive Micro- computer LSI offers high measurement accuracy. * The instrument offers high power of emission and a wide spectrum of receiving sensitivity. -
Page 8: Specifications
12.2 Specifications Display: 4 digits, 10mm LCD Range: 1.2-225mm (45# steel) Resolution: 0.1mm / 0.001 inch Accuracy: ± (0.5%n+0.1) Sound velocity: 500 to 9000m/s Power supply: 4×1.5V AAA (UM-4) battery Operating conditions: Temperature: 0 to 50°C Humidity: <80% Dimensions: 120 x 62 x 30mm (4.7 x 2.4 x 1.2 inch) Weight: about 164g (batteries not included) Accessories:... -
Page 9: Material Selection
3-11 Coupling indicator 3-12 Base plate 3-13 Velocity key 3-14 RS-232C interface 12.4 Material selection a) The instrument has to be switched on by the Power- key 3-4. b) The code `cdxx` or `xxxx` will be shown on the display 3-2. `cd` is the abbreviation for `code` and `xx` is a number among 0.1 and 11 which stands for the material to be measured as shown in the scale below. -
Page 10: Calibration
f) To get into the menu selection of the material code, the Material selection key 3-5 has to be pressed. To quit the menu, material selection key has to be pressed again or it has to be waited until the instrument- after a few seconds- changes back into measurement mode. -
Page 11: Battery Replacement
Ultrasound velocity can be adjusted by pressing the Plus- or the Minus- key. By do- ing this, the value shown in the display is changed higher or lower. First the in- crease is 10m/ s. If the Plus- or Minus- key is pressed for longer than 4 seconds, the increase is 100m/ s.