Assembling-Adjusting; Connecting The Motor To The Power Supply; Motor Specifications; Safety Precaution - Craftsman ACCRA-ARM 113.29003 Assembly & Operating Instructions

Your
I. Arbor Wrench
2. Shaft Wrench
3o Table Clamp
4_ Adapter Plug
5. Yoke Clamp Handle
6_ Radial Arm Indicator
7. Carriage Lock Knob
8_ Rip Scale Indicator
9. Swivel Latch Pin Knob
10_ Latch Pin Handle
11. Switch Key
12, Arm Latch Handle
13, Bevel Index Handle
14, Discharge Elbow
15. Anti Kick Back Pawl Assembly
16o Bevel Lock Knob
17o Bevel Index Scale and indicator
18. Elevation Crank
19. Hex "L" Wrenches
Figure 5
ASSEM BLI N G -ADJ USTIN G
CONNECTING THE MOTOR TO THE POWER SUPPLY
Motor Spec_cations
115/230 volt, 10/5 amps, 3450 RPM, 60 cycle, alternating
current (AoC. only) single phase, non-reverslbteo Rotation:
clockwlse viewing saw blade end of motor shaft.
The motor as shipped is connected for 115 volts_ For 115
volt operation see Figures 6 and 7 for connecting plug
and cord from saw into 115 volt receptacle.
Safety Precaution
The saw motor is equipped with a manual reset, therme]
oveHoad protector. If during operation this protector opens
the line, immediately turn the switch "Off". The protector
can be closed again after the motor has cooled by firmly
pushing the red button on the capacitor cover until the
protector snaps into the running position. Do not tap or
strike the reset button_ This protector is not intended to
take the place of a fuse as the protector will not provide
protection against overloads or short circuits in the lines
leading to the motor. The motor should not be operated on
a load which ca usesthe protector to open the line frequently°
For circuit protection use a "Fustat" or "'Fusetran" fuse
--15 ampere fuse for 115 volt operation and 7½ am-
pere fuse fop 230 volt operation.
PLUa AND CO_D _ _)_ |
FROM SAW
GI_OUND LLtO
115 VOLT
SUPPLY t|NE
GROUND WtlE
Figure 6
For 230 volt operation, see connecting instructionson motor
nameptateo Also see the "Warning Label" on the rear of
the saw base°
"'IMPORTANT" The fat!owing wire sizes ore recommended
for connecting the motor to o power source for TROUBLE
FREE OPERATION.
Length of Wife Size R_quired
Concluctor (Ame_iconWire Gaug_ No,)
115 Volt Lines
50 feet or tess No, 12
100 feet or less No. 10
• 100 feet to 150 feet No, 8
150 feet to 200 f_et No. 6
200 feet to 400 f_et He. 4
230 Volt Lines
50 feet or less No_ 14
100 feet or less Hoe 12
100 feet to 150 feet No. 10
150 feet to 200 feet No. 8
200 feet to 400 feet No_ 6
For circuitsof greater length the wire size must be increased
proporfiohally.
ALWAYS GROUND _--_'_------_'_
PIGTAIL TO
115 VOLT
SUPPLY LINE
PLUG AND CORD
FROM SAW
METAL t_ECEPTACLE _OX
"_ MUST _E GROUHDED TO
A COLD WATER PIPE OR
TO THE ELECTRICAL GROUND
OF THE INCOM|NG
ADAFTER PLUG POWER LINES
_ITEM 4, P_GUeE S _
Figure 7
7