Related Manuals for Oliver MODEL 619-MDP
Summary of Contents for Oliver MODEL 619-MDP
- Page 1 Walker, Michigan, U.S.A. 49534 USER’S OPERATING AND INSTRUCTION MANUAL MODEL 619-MDP DOUGH PRESS 0619S20000-CV3...
-
Page 2: Table Of Contents
619-MDP DOUGH PRESS INDEX Section Description Document No. Page No. SAFETY INSTRUCTIONS -------------------------------------- 0619S20141 --------------------------- 1-1 DESCRIPTION/SPECIFICATIONS --------------------------- 0619S20130---------------------------- 2-1 Description -------------------------------------------------------------------------------------------------- 2-1 Physical Specifications----------------------------------------------------------------------------------- 2-1 Electrical Specifications---------------------------------------------------------------------------------- 2-2 Electrical Wiring Diagrams ----------------------------------------------------------------------------- 2-1 OPERATING INSTRUCTIONS -------------------------------- 0619S20131 --------------------------- 3-1 Before You Start ------------------------------------------------------------------------------------------- 3-1 Basic Operation -------------------------------------------------------------------------------------------- 3-1 MAINTENANCE --------------------------------------------------- 0619S20148 --------------------------- 4-1... - Page 3 INDEX (Continued) REPLACEMENT PARTS SECTION (Continued) Section Description Document No. Page No. COVER ASSEMBLY --------------------------------------------- 0619S20144 --------------------------- 8-1 Drawing ------------------------------------------------------------------------------------------------ 8-1 Parts List ----------------------------------------------------------------------------------------------- 8-2 Parts List ----------------------------------------------------------------------------------------------- 8-3 HYDRAULIC ASSEMBLY -------------------------------------- 0619S20137 --------------------------- 9-1 Drawing ------------------------------------------------------------------------------------------------ 9-1 Parts List ----------------------------------------------------------------------------------------------- 9-2 LID ASSEMBLY -------------------------------------------------- 0619S20138 -------------------------- 10-1 Drawing ----------------------------------------------------------------------------------------------- 10-1 Parts List ---------------------------------------------------------------------------------------------- 10-2...
-
Page 4: Safety Instructions
619-MDP DOUGH PRESS SAFETY INSTRUCTIONS Every effort has been made by Oliver Products Company to provide you with a safe machine. It is essential, however, that machine operators and maintenance personnel observe the following safety precautions. 1. Before attempting to operate your dough press read this manual. Never allow an untrained person to operate this machine. - Page 5 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 6: Description/Specifications
DESCRIPTION/SPECIFICATION Description The Oliver dough press consists of a hopper which can be loaded with dough from an approximate minimum of ten and one half pounds up to forty pounds, (depending on the density of the dough). The lid and sides of the hopper are made of hard anodized and Teflon impregnated cast aluminum. -
Page 7: Electrical Specifications
Physical specifications (continued) Net Weight: Approximately 455 pounds. Shipping Weight: Approximately 500 pounds. Product Capacities: Fill Capacity (approximate) = 10-1/2 to 40 pounds Electrical Specifications 2 Horse Power, 1 phase, 60 hertz, 230 Volts AC, 10 Amps. 2 Horse Power, 3 phase, 60 hertz, 208 Volts AC, 6.5 Amps. 2 Horse Power, 3 phase, 60 hertz, 230 Volts AC, 6.2 Amps. - Page 8 Electrical Wiring Diagrams (Continued) 3 ph, 60 hz, 208/230 VAC 3 ph, 60 hz, 460 VAC 0619S20130...
-
Page 9: Operating Instructions
619-MDP DOUGH PRESS OPERATING INSTRUCTIONS Before You Start CAUTION THE DOUGH PRESS SHOULD ONLY BE PLUGGED INTO AN OUTLET WITH THE SAME VOLTAGE AS STATED ON THE NAMEPLATE Before starting a new dough press with THREE PHASE electrical power for the first time you should check to see if the motor is running in the correct direction. - Page 10 Basic Operation (Continued) · Close the lid and turn the handle in a clockwise direction making sure it is secure. · With the machine running grasp the control valve handle and lift it to start the floor of the hopper up. Hold it in this position until the light on the starter switch box comes on, the light indicates that the preset pressing pressure has been achieved.
-
Page 11: Maintenance
619-MDP DOUGH PRESS MAINTENANCE WARNING ALWAYS MAKE SURE THE MACHINE HAS BEEN DISCONNECTED FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING Cleaning Remove- all scraps from lower pan. Open side doors and brushing out all scraps. Wash all interior surfaces; Knives, pusher plates, hopper, lid surface with a damp rag and mild soap solution. - Page 12 ******W A R N I N G****** UNPLUG MACHINE USING THE ACCESS DOORS ON BOTH SIDES OF THE UNIT PULL DOOR UP, USE ONE HAND TO HOLD DOOR UP WIPE DOWN MACHINE WITH OTHER, USING A RAG OR A BRUSH 0619S20148...
-
Page 13: Lubrication
Lubrication The machine requires no lubrication but the oil level in the hydraulic system should be checked periodically. To check the oil level remove the rear cover by removing the four knobs which secure it to the divider, then remove the tank breather/cap and determine where the top of the oil is in relation to the top surface of the tank. -
Page 14: Replacing The Locking Hook Or Cam
Replacing The Locking Hook Or Cam: · Remove the lid cover by removing the four screws which secure it in position. · Detach the spring from the hook. · Open the lid. · Turn the handle until the pin securing the cam to the shaft is in line with the notch in the locking hook. -
Page 15: Replacing The Hydraulic Cylinder
Replacing The Hydraulic Cylinder · Turn the machine on and raise the pressing plate to the top of the hopper and then turn the dough press off and disconnect it from the power supply. · To remove the hydraulic cylinder the front, rear, and side panels must be removed from the machine. -
Page 16: Changing The Pump Or Coupling
Changing The Pump Or Coupling · Disconnect the machine from the power supply. · Remove the rear cover and the “Motor Side” panels. · Loosen the intake hose at the pump, make sure you have something available to catch the hydraulic oil leaking from the end of the hose when it is disconnected. ·... -
Page 17: Troubleshooting
619-MDP DOUGH PRESS TROUBLE SHOOTING GUIDE The “Ram Up Light” does not come on. Possible Causes · There may be a disconnected wire. · The pilot light may have burnt out. · The pressure switch is not operating and needs replacement. The motor “Hums”... -
Page 18: The Motor Runs Slowly But Stalls Easily Before Completion Of Its Stroke
The motor runs “Slowly” but stalls easily before completion of its stroke. Possible Causes · The motor is wired for high voltage but is connected to a low voltage supply. Trouble Shooting (Continued) The motor has “Stalled” and can not be restarted. Possible Causes ·... -
Page 19: Recommended Spare Parts
619-MDP DOUGH PRESS RECOMMENDED SPARE PARTS PART NUMBER PART DESCRIPTION NO. REQ’D. 7024-6101 Extension Spring 7030-0024 LH Lid Spring 7030-0023 RH Lid Spring 5835-7636 Coiled Pin 5114-9556 Hydraulic Filter 5757-8518 Pressure Switch 5709-9924 Starter Enclosure 5709-0191 Pilot Light 5709-3040 Motor Starter (3-60-460V) 5709-3041 Motor Starter (3-60-230V) 5709-3042... -
Page 20: Main Frame Assembly
619-MDP DOUGH PRESS MAIN FRAME 0619S20135... -
Page 21: Parts List
MAIN FRAME PARTS LIST ITEM NO PART DESCRIPTION PART NUMBER Base 0620-0008 Caster-Swivel 5902-2377 Caster-Rigid 5902-2378 Brace-Lower 0620-0006-001 Brace-Front Lower 0620-0006-002 Plate-Cylinder Support 0620-0007-001 Panel-Separation 0620-0032 Grommet-Edging Nylon 5767-1240 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 0619S20135... -
Page 22: Cover Assembly
619-MDP DOUGH PRESS COVER ASSEMBLY 0619S20144... -
Page 23: Parts List
COVER ASSEMBLY PARTS LIST Stainless Steel Covers ITEM NO PART DESCRIPTION PART NUMBER Chute Dough 0619-0027-008 Plate Handle Backing 0619-0028 Deflector 0619-0043 Cover Top 0620-0001-001 Cover-Side W/Cleaning Door 0620-0029-008 Cover-Side W/Chute % W/Cleaning door 0620-0029-009 Cover-Front 0620-0030-003 Cover Rear 0620-0031-001 Guard-Switch 0620-0106 Door Access Cleaning... - Page 24 Cover-Side W/Cleaning Door 0620-0029-006 Cover-side W/Chute & W/C Door 0620-0029-007 Cover-Front 0620-0030 Cover Rear 0620-0031 Guard-Switch 0620-0106 Door Access Cleaning 0620-0121 Hinge Door Access 0620-0122 Screw-Thumb 5843-0536 Handle Recessed 5908-5046 Handle Pull 0620-0123 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 0619S20144...
-
Page 25: Hydraulic Assembly
619-MDP DOUGH PRESS HYDRAULIC ASSEMBLY Rev. 10/25/05 0619S20137... - Page 26 Fitting-Adapter 5115-2095 Switch-Pressure 5757-8518 Valve-Check 5148-5217 Spacer-Pump/Flange 0619-0044 Items Not Shown on Drawing Hose-Pump High Pressure 5121-8235 Hose-Upper Cylinder 5121-8174 Hose-Valve to Lower Cylinder 5121-8187 Hose-Valve to Relief 5121-8196 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 Rev. 04/23/18 0619S20137...
-
Page 27: Lid Assembly
619-MDP DOUGH PRESS LID ASSEMBLY 0619S20138 10-1... - Page 28 7030-0023 Spring-LH Torsion 7030-0024 Ring-Retaining 5840-1127 Clamp-Spring 0620-0034 Shaft-Handle 0620-0036 Hook-Locking 0620-0017-3 Cam-Latch 0620-0037-1 Pin-Coiled 5835-7636 Screw-Socket Set (Oval Point) 5842-6479 Bracket-Spring 0620-0035 Spring-Extension 7024-6101 0619-0019-002 Rod-Handle 0619-0018-002 Knob 5911-7003 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 0619S20138 10-2...
-
Page 29: Pusher Assembly
619-MDP DOUGH PRESS PUSHER ASSEMBLY 0619S20139 11-1... - Page 30 Brace-Front Upper Adj. W/Holes 0620-0002-005 Brace-Front Upper Center Adj. 0620-0003-003 Brace-Upper Adj. 0620-0063-002 Hex Adjustable 0619-0026-001 Catch 0620-0067-1 Shim-(.030) 0619-0029-001 Shim-(.048) 0619-0029-002 Shim-(.060) 0619-0029-003 Plate-Backing 0620-0076 Plate Pressing 0620-0077 Insert-Threaded 5822-2030 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 0619S20139 11-2...
-
Page 31: Electrical Assembly
619-MDP DOUGH PRESS ELECTRICAL ASSEMBLY 0619S20140 12-1... - Page 32 Cord-Motor (3-60-208/230) 0620-0073 Cord-Motor (3-60-460) 0620-0071-001 Cord-Motor (1-60-230) 0620-0038 Cord-Power (3-60-208/230) 0643-0033-001 Cord-Power (3-60-460) 0620-0105 Cord-Power (1-60-230) 0620-0039 Cord-Pressure Switch 0619-0042 Cap-Plug (1-60-230) 5765-2030 * For other Electrics consult factory FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 0619S20140 12-2...
- Page 33 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 34: Warranty
WARRANTY PARTS Oliver Packaging & Equipment Company warrants that if any part of the equipment (other than a part not manufactured by Oliver Packaging & Equipment ) proves to be defective (as defined below) within one year after shipment, and if Buyer returns the defective part to Oliver Packaging &... - Page 35 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 36: Warranty Procedure
4. The service dealer will then complete an invoice and send it to the Parts and Service Department at Oliver Packaging & Equipment Company. 5. The Parts and Service Manager of Oliver Packaging and Equipment Company will review the invoice and returned parts, if applicable, and approve for payment. - Page 37 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 38: Returned Parts Policy
This policy applies to all parts returned to the factory whether for warranted credit, replacement, repair or re-stocking. Oliver Packaging and Equipment Company requires that the customer obtain a Return Material Authorization (RMA) number before returning any part. This number should appear on the shipping label and inside the shipping carton as well.