Related Manuals for Oliver MODEL 619-16
Summary of Contents for Oliver MODEL 619-16
- Page 1 Walker, Michigan, U.S.A. 49534 USER’S OPERATING AND INSTRUCTION MANUAL MODEL 619-16 MODEL 619-20 MODEL 619-24 MODEL 619-24R DOUGH DIVIDERS 0619S20000-CVR...
- Page 2 MODEL 619-16,20,24,&24R DOUGH DIVIDERS INDEX SAFETY INSTRUCTIONS................0619S20001 DESCRIPTION/SPECIFICATIONS.............0619S20002 Description/Dimensional Specifications......... 0619S20002-1/3 Electrical Specifications/Wiring Diagrams........0619S20002-2/3 OPERATION INSTRUCTIONS..............0619S20003 MAINTENANCE..................0619S20149 Cleaning..................0619S20149-1/7 Cleaning..................0619S20149-2/7 Lubrication..................0619S20149-3/7 Hydraulic Oil Specifications............0619S20149-3/7 Hydraulic Filter Replacement............0619S20149-3/7 Removing The Lid................0619S20149-3/7 Replacing The Locking Hook Or Cam..........0619S20149-3/7 Replacing Plastic Bottom Element..........
-
Page 3: Safety Instructions
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS SAFETY INSTRUCTIONS Every effort has been made by Oliver Products Company to provide you with a safe machine. It is essential however, that machine operators and maintenance personnel observe the following safety precautions. -
Page 4: Overall Machine Dimensions
DESCRIPTION/SPECIFICATION Description: The Oliver divider consists of a hopper which can be loaded with dough from a minimum of ten and one half pounds up to forty-five pounds. The lid and sides of the hopper are made of heavy cast aluminum. The moveable hydraulic floor of the hopper is made of a collection of food grade plastic plates which, when moved upward, will compress the dough until it completely fills the remaining area. - Page 5 Physical specifications (continued) Net Weight: Approximately 455 pounds. Shipping Weight: Approximately 500 pounds. Product Capacities: Fill Capacity (approximate) = 10-1/2 to 45 pounds Divided piece Size (approximate): 16 part dividers = 10-1/2 to 45 ounces 20 part dividers = 8-1/2 to 36 ounces 24 part dividers = 7 to 30 ounces Electrical Specifications 2 Horse Power, 1 phase, 60 hertz, 230 Volts AC, 10 Amps.
- Page 6 Electrical Wiring Diagrams (Continued) 3 ph, 60 hz, 208/230 VAC 3 ph, 60 hz, 460 VAC Rev. 5-24-96 0619S20002-...
- Page 7 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS OPERATING INSTRUCTIONS Before You Start CAUTION THE DIVIDER SHOULD ONLY BE PLUGGED INTO AN OUTLET WITH THE SAME VOLTAGE AS STATED ON THE NAMEPLATE Before starting a new divider with THREE PHASE electrical power for the first time you should check to see if the motor is running in the correct direction.
- Page 8 Basic Operation (Continued) · Open the lid and load the preweighed dough into the hopper. Spread the dough over the floor of the hopper making it approximately the same height, this is done to eliminate large air pockets and to insure equal division of the dough. ·...
- Page 9 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS MAINTENANCE WARNING ALWAYS MAKE SURE THE MACHINE HAS BEEN DISCONNECTED FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING. Cleaning Remove- all scraps from lower pan. Open side doors and brushing out all scraps. Wash all interior surfaces;...
- Page 10 *********W A R N I N G****** UNPLUG MACHINE USING THE ACCESS DOORS ON BOTH SIDES OF THE UNIT PULL DOOR UP, USE ONE HAND TO HOLD DOOR UP WIPE DOWN MACHINE WITH OTHER, USING A RAG OR A BRUSH Lubrication The machine requires no lubrication but the oil level in the hydraulic system should be checked periodically.
- Page 11 Hydraulic Filter Replacement At least once a year the throw-away filter on the hydraulic system should be replaced, more often when under heavy use. To replace the filter remove the front cover unscrew the old filter and replace it with a new one. The filter is located on the return line near the tank. Removing The Lid ·...
- Page 12 · Remove the nut securing the float to the thrust plate. · Using a block of wood or other soft material to protect the threads on the float, force the float and bottom element assembly upwards until it is free from the thrust plate and then lift the assembly from the blades.
- Page 13 · Remove one of the center float assemblies, (see above procedures). Once this has been done the bolt securing the thrust plate to the cylinder rod can be removed using a universal socket style wrench. · Remove the four screws securing the star to the outer cylinder rod. ·...
- Page 14 · Once the installation has been completed it IS NOT necessary to adjust the pressure relief valve to allow proper operation of the divider. Note: Oliver’s valves are normally preset at the factory and adjustment IS NOT necessary. Should it become necessary to change the pressure relief setting follow the two steps given below.
-
Page 15: Troubleshooting Guide
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS TROUBLE SHOOTING GUIDE The End of Stroke Light does not come on. Possible Causes · There may be a disconnected wire. · The bulb may have burnt out. · The limit switch is not adjusted properly. - Page 16 Possible Causes · The overload relay has tripped. Allow the relay about five minutes to cool and attempt to restart the divider. The divider is not cutting properly. Possible Causes · Dough scraps and flour have accumulated between the blade holder and the float plate.
-
Page 17: Part Description
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS RECOMMENDED SPARE PARTS PART NUMBER PART DESCRIPTION NO. REQ’D. 7024-6101 Extension Spring 4605-1000-0028 LH Lid Spring 4605-1000-0029 RH Lid Spring 5835-7636 Coiled Pin 5114-9556 Hydraulic Filter 0620-0047 Blade Holder Brace 0620-0012-1 Star Plate... - Page 18 RECOMMENDED SPARE PARTS (Continued) PART NUMBER PART DESCRIPTION NO. REQ’D. SPARE PARTS FOR MODEL 619-24R ONLY 0620-0011-001 Blade Holder 0620-0048-001 Plastic Outside Plate 0620-0049-001 Plastic Inside Plate 0620-0052-002 Large Lower Blade 0620-0053-002 Large Upper Blade 0620-0054-002 Small Blade 0620-0055-002 Outside Blade OPTIONAL SPARE PARTS 0620-0036 Handle Shaft...
- Page 19 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS PARTS LIST ITEM NO. PART DESCRIPTION PART NO. Brace-Lower W/Holes 0620-0005-001 Brace-Lower 0620-0006 Plate-Cylinder Support 0620-0007-001 Base 0620-0008 Plate-Star 0620-0012-1 Panel-Separation 0620-0032 Actuator-Limit Switch 0620-0044-1 Spacer-Cylinder Rod 0620-0045 Caster-Ridged 5902-2378 Caster-Swivel W/Brake...
- Page 20 PARTS LIST ITEM NO. PART DESCRIPTION PART NO. Hose Clamp 5106-8087 Filter Head 5114-9554 Filter-Spin On 5114-9556 Cylinder-Custom Hydraulic 5108-7818 Flange-Tank 5115-0388 Fitting-Elbow 5115-2090 Fitting-Hose 5115-2079 Fitting-Adapter 5115-4031 Fitting-Adapter 5115-4032 Hose-Bottom Cylinder 5121-8169 Flange-Pump Mounting 5137-7375 Hose-Pump 5121-8173 Hose-Upper 5121-8174 Hose-Hydraulic 0619-0016 Pump-Vane...
- Page 21 PARTS LIST ITEM NO. PART DESCRIPTION PART NO. Plate-Thrust (619-24R) 0620-0009-002 Separator-Cleaning 5503-4301 Blade Holder (619-16) 0620-0011-002 Blade Holder (619-20) 0620-0011 Blade Holder (619-24R) 0620-0011-001 Top Cover 0620-0013 Round Hopper 0619-0021-001 Brace-Blade Holder 0620-0047 Plate-Plastic Outer (619-16) 0620-0048-002 Plate-Plastic Outer (619-20) 0620-0048-003 Plate-Plastic Outer (619-24R) 0620-0048-001...
- Page 22 PARTS LIST ITEM NO. PART DESCRIPTION PART NO. Plate-Square Plastic 0620-0062-001 Rear Upper Brace Adjustable 0620-0063-003 Holder-Square Blade 0620-0064 Blade-Upper (619-24) 0620-0065-001 Blade-Lower (619-24) 0620-0066-001 Catch 0620-0067 Hex-Adjustable 0619-0026 Plate-Hopper Side W/Chute 0620-0061-001 Bracket-Limit Switch 0620-0041-001 Bracket-Starter 0620-0042-1 Enclosure-Manual Starter 5709-9924 Pilot Light 5709-0191...
- Page 23 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERSMAIN FRAME ASSEMBLY DRAWING REV. 4-23-97 0619S20008...
- Page 24 COVERS ASSEMBLY DRAWING FRAME ASSEMBLY 0619S20145...
- Page 25 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS HYDRAULIC ASSEMBLY DRAWING Rev. 12/21/04 0619S20010...
-
Page 26: Lid Assembly Drawing
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS LID ASSEMBLY DRAWING REV. 1-23-02 0619S20011... - Page 27 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS 16 PART PUSHER ASSEMBLY DRAWING REV. 5-30-00 0619S20043...
- Page 28 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS 20 PART PUSHER ASSEMBLY DRAWING REV. 5-30-00 0619S20012...
- Page 29 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS 24 PART SQUARE PUSHER ASSEMBLY DRAWING REV. 5-30-00 0619S20013...
- Page 30 MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS 24 PART ROUND PUSHER ASSEMBLY DRAWING REV 5-30-00 0619S20044...
- Page 31 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 32: Warranty
WARRANTY PARTS Oliver Packaging & Equipment Company warrants that if any part of the equipment (other than a part not manufactured by Oliver Packaging & Equipment ) proves to be defective (as defined below) within one year after shipment, and if Buyer returns the defective part to Oliver Packaging &... - Page 33 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 34: Warranty Procedure
4. The service dealer will then complete an invoice and send it to the Parts and Service Department at Oliver Packaging & Equipment Company. 5. The Parts and Service Manager of Oliver Packaging and Equipment Company will review the invoice and returned parts, if applicable, and approve for payment. - Page 35 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 36: Returned Parts Policy
This policy applies to all parts returned to the factory whether for warranted credit, replacement, repair or re-stocking. Oliver Packaging and Equipment Company requires that the customer obtain a Return Material Authorization (RMA) number before returning any part. This number should appear on the shipping label and inside the shipping carton as well.