Eaton 600 A PUSH-OP Operation Instructions Manual
Deadbreak connectors
Hide thumbs
Also See for 600 A PUSH-OP:
- Operation instructions manual (12 pages) ,
- Installation instructions (4 pages) ,
- Assembly/installation instructions (20 pages)
Related Manuals for Eaton 600 A PUSH-OP
Summary of Contents for Eaton 600 A PUSH-OP
- Page 1 COOPER POWER Deadbreak Connectors SERIES Effective May 2017 MN650011EN Supersedes June 2010 (S600-13-1) 600 A PUSH-OP™ deadbreak connector operation instructions...
- Page 2 CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other- wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or...
-
Page 3: Table Of Contents
Reconnecting cable to apparatus bushings ............7 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017... -
Page 4: Safety Information
FOR LIFE FOR LIFE Eaton meets or exceeds all applicable industry standards relating to product safety in its Cooper Power™ series products. We actively promote safe practices in the use and maintenance of our products through our service literature, instructional training programs, and the continuous efforts of all Eaton employees involved in product design, manufacture, marketing, and service. -
Page 5: Product Information
Unpack the Introduction PUSH-OP connector and inspect it thoroughly for damage Eaton's Cooper Power™ series 600 A, 15, 25, and 35 kV incurred during shipment. If damage is discovered, file a Class PUSH-OP™ deadbreak connector offers a complete claim with the carrier immediately. -
Page 6: Operating Instructions
PUSH PLATE SLOTS HITCH PIN PUSH PLATE BAIL BRACkET 200 A INTERFACE SHROUD PIN OPERATING EYE LOCkING SLOT PUSH-OP CONNECTOR OR PUSH-OP BUSHING ADAPTER figure 3. Line illustration of the PuSH-oP connector. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017... -
Page 7: Isolating And Grounding A Cable Requiring Repair
Refer to Figure 5. Test for voltage by fuzzing or by using voltage detector • designed for connectors. Remove probe after testing. figure 6. Provide a visible ground with a grounding elbow. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017... - Page 8 Ensure that PUSH-OP bail bracket on the insulated standoff bushing is unlatched. Refer to Figure 7 . figure 8. unthread the hitch pin. figure 7. Mount PuSH-oP standoff bushing. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
- Page 9 Thread hitch pin clockwise until bail lock is secured. remove the grounding elbow from the 200 A interface • during this operation. Refer to Figure 10. figure 10. Move PuSH-oP connector to insulated bushing. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
- Page 10 Refer to Figure 13. figure 14. Pull on push plate to ensure latch plate is engaged. figure 13. install adapter on PuSH-oP apparatus bushing. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
-
Page 11: Reconnecting Cable To Apparatus Bushings
Remove bushing adapter by unhooking catch strap ring. Place bushing adapter in clean protected area. Refer to Figure 18. figure 16. Engage catch strap in push plate slots. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017... - Page 12 Refer to Figure 19. figure 19. Pull back until connector is unsealed. figure 21. Pull on push plate to ensure latch plate is engaged. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
- Page 13 22. Place cap on 200 a connector interface. Repeat Steps 1 and 2 for all three phases on both ends of cable. Remove all tool, test equipment and personal protective equipment from work area before energizing apparatus. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
- Page 14 This page intentionally left blank. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
- Page 15 This page intentionally left blank. 600 A PUSH-oP DeADbreAk connector oPerAtion inStrUctionS MN650011EN May 2017...
- Page 16 Eaton.com/cooperpowerseries © 2017 Eaton All Rights Reserved Eaton is a registered trademark. Publication No. MN650011EN For Eaton's Cooper Power series product kA20480492 Rev 01 information call 1-877-277-4636 or visit: All trademarks are property (Supersedes kA20480492 Rev 00) of their respective owners.
Need help?
Do you have a question about the 600 A PUSH-OP and is the answer not in the manual?
Questions and answers