Setting Schedules - Honeywell ADEMCO VISTA SERIES Programming Manual

SETTING SCHEDULES

(Installer Code + [#] + [6] [4])
The system provides schedules, which can be used to automatically control 11 types of system events at pre-defined times.
Some events are reserved for the installer only.
VISTA-20P: Provides up to 32 schedules: 16 schedules for use by the end-user, 16 for use by the installer.
VISTA-15P: Provides up to 8 schedules: 4 schedules for use by the end user, 4 for use by the installer.
NOTES:
• The master code can only access schedules 01-16 (VISTA-15P = 01-04) and events 00-07.
• System clock must be set before schedules can take effect.
• Programmed schedules do not take effect until the next scheduled "start" time. (e.g., if programming a schedule time window
for 8AM to 5PM, the schedule does not take effect until 8AM after the schedule has been programmed.)
Schedule Mode
E N T E R S C H E D N O .
0 0 = Q U I T 0 0
E N T E R E V E N T
D E V I C E N U M B E R
XX
G R O U P N U M B E R
X
P A R T I T I O N
X
S T A R T S M T W T F S
0 0 1 0 0 0 0
H H M M A M
S T O P S M T W T F S
0 0 1 0 0 0 0
H H M M A M
Schedule Number
VISTA-20P
01-16 = end-user schedules
17-32 = installer-only
VISTA-15P
01-04 = end-user schedules
05-08- = installer-only
[∗] to continue
Enter Event
00 = clear event
01 = Relay On/Off
02 = User Access
03 = Latch Key Report to
Pager
04 = Forced Stay Arming †
†
05 = Forced Away Arming
06 = Auto Disarm
07 = Display "Reminder"
10 = Display custom words
†††
11 = Periodic Test Report
Press [∗] to continue.
Device Number
V20P:
01-18 = device number
V15P: 01-08, 17, 18
Press [∗] to continue.
Group Number
1-8 = group number
Press [∗] to continue to the
"Start" prompt.
Partition
0 = all partitions
1 = partition 1
2 = partition 2
3 = common
Press [*] to continue to the
"Start" prompt.
Start Time
01-12 = hour
00-59 = minute
0 = AM; 1 = PM
Days = place "1" under days
Press [∗] to continue.
Stop Time
01-12 = hour
00-59 = minute
0 = AM; 1 = PM
Days = place "1" under days
Press [∗] to continue.
Enter the desired schedule number.
To Quit, enter 00.
Enter the desired event number for event you want to occur at a
specified time.
Events 10-11 are reserved for the installer only.
Latch key report (option 03) is sent to all pagers in the user's
partition and is active only when the system is armed (message
sent is 777-7777). User must be enabled for paging (see User
Attributes in System Operation section).
† Forced bypass is automatically enabled regardless of setting
in field *23.
†† If selected, system displays custom words 8, 9, and 10 at
††
defined time. Can be used as installer's reminder message to
the end user.
††† See key commands in Test Report Code data field *64
section to quickly set periodic test reporting intervals.
NOTE: Events 07 and 10 cause the keypad to beep every 30 seconds
when messages are displayed. Stop the beeps by pressing any key.
(For event 01-relay on/off)
Enter the physical device number as programmed in ∗79 Menu
Mode, then press [*] to continue to the "Start" prompt.
Device numbers 17 and 18 designate built-in triggers 1 and 2
respectively.
(For event 02-user access)
(V20P only; for events 03-07, 10)
Enter the event's start time and days of the week to occur.
To select days, position the cursor under the desired days using
the [∗] key to move forward, then press "1" to select the day.
(For events 01-relay on/off; 02-user access; 03-latch key report)
Enter the event's stop time and days of the week to occur.
To select days, position the cursor under the desired days using
the [∗] key to move forward, then press "1" to select the day.
– 32 –