Remote Control; Laser Pointer Function - Sanyo PLC WXU700A Owner's Manual

Part Names and Functions

Remote Control

①
③
⑤
④
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑭
⑮
⑯
⑰
① L-CLICK button
Act as the left mouse button for wireless mouse
operation. (p.15)
② ON/STAND-By button
Turn the projector on or off. (pp.21-23)
③ WIRED REMOTE jack
Connect the remote control cable(not supplied)
to this jack when using as a wired remote control.
Wireless remote control does not work when the
remote control cable is connected to the projector.
④ SIGNAL EMISSION indicator
Lights red while the laser beam is being emitted
from the laser light window or a signal is being sent
from the remote control to the projector.
Note:
To ensure safe operation, please observe the
following precautions:
– Do not bend, drop, or expose the remote control to
moisture or heat.
– For cleaning, use a soft dry cloth. Do not apply
benzene, thinner, spray, or any chemical material.
1
⑤ LASER LIGHT window
A laser beam is emitted from here (p.14).
⑥ HDMI button
Select the HDMI input source. (pp.28,41)
⑦ COMPUTER button
Select the COMPUTER input source. (pp.30-31, 41)
②
⑧ INFO . button
Operate the information function. (p.63)
⑨ KEySTONE button
Correct keystone distortion. (pp.26, 49)
⑩ Point ▲▼◄► ( VOLUME + / – ) buttons
–Select an item or adjust the value in the On-Screen Menu. (p.24)
㉙
–Pan the image in the Digital zoom + mode. (p.39)
–Adjust the volume level. (Point◄►buttons) (p.27)
㉘
⑪ MENU button
Open or close the On-Screen Menu. (p.24)
㉗
⑫ FREEZE button
Freeze the picture on the screen. (p.28)
⑬ LASER button
⑭ PAGE ▲▼ buttons
㉖ Scroll back and forth the pages on the screen when giving a presentation. To use
these buttons, connect the projector and your computer with a USB cable. (pp.10,
17)
㉕
⑮ LAMP button
Select a lamp mode. (pp.28, 58)
⑯ D .ZOOM +/- buttons
㉔
Zoom in and out the images. (pp.28, 39)
⑰ RESET/ON/ALL-OFF switch
㉓
When using the remote control, set this switch to "ON." Set it to "ALL OFF" for
power saving when it is not used. Slide this switch to "RESET" to initialize the
㉒
remote control code or switch Spotlight and Pointer to the Laser pointer function.
(pp.13-14)
㉑
⑱ PIP button
Operate the Picture In Picture function. (pp.28,55)
⑳
⑲ SCREEN button
Select a screen mode. (pp.29,38-39,46)
⑲
⑳ IMAGE button
⑱
Select the image mode. (pp.29,36,43)
㉑
MUTE button
Mute the sound. (p.27)
㉒
P-TIMER button
Operate the P-timer function. (p.29)
㉓ NO SHOW button
Temporarily turn off the image on the screen. (p.29)
㉔ R-CLICK button
Act as the right mouse button for wireless mouse operation. (p.15)
㉕ SELECT button
– Execute the selected item. (p.24)
– Expand or compress the image in Digital zoom mode. (p.39)
㉖ PRESENTATION POINTER button
Move a pointer of the projector or a pointer for wireless mouse operation. (pp.14-15)
㉗ AUTO SET/CANCEL button
– Correct vertical keystone distortion and adjust computer display parameters such
– Display the image in USB thumb drive or return to the menu bar in Memory
㉘ NETWORK button
Operation" and owner's manual of "Memory viewer function".
㉙ VIDEO button
Select the VIDEO input source. (pp.28,40)
– Operate the Laser pointer function. Laser beam is emitted while pressing this
button within 1 minute. When using this laser pointer for more than 1 minute,
release the LASER button and press it again. (p.14)
– Display the Pointer on the screen. (p.14)
as Fine sync, Total dots, Horizontal and Vertical position
Viewer menu.
Refer to the owner's manual of "Memory viewer function".
Select the Network input. See the owner's manual of "Network Set-up and
.
(pp.26, 48)