KI RT Assembly Instructions

Detail A
leveling glide
Assembly Instructions
Figure 1
Detail A
leveling glide
Assembly Instructions
WorkUp Adjustable Table
November 2016
M8 x 20mm
screw
flat
washer
foot
column
WorkUp Electric Height Adjustable Tables
Model RT
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
M8 x 20mm
may result in assembly failure and personal injury.
screw
flat
washer
foot
on a clean flat floor.
Note : When tightening the M8 screws, first
twist in all four screws "finger tight", then
tighten the screws one quarter turn at a time
using a diagonal tightening pattern as shown
in Detail A. Repeat the diagonal pattern until
Model RT
all four screws are tight (Detail A & Figure 1).
Assemble Feet To Columns
1. Set the column on end with the smaller
Tools Required
(inner) square tube on the floor. The
• #3 Phillips Screwdriver
threaded holes visible on the end of the
• 5mm Hex Key
column will be in a rectangular (not square)
Note: Before discarding any
pattern (Figure 1) .
packaging confirm all components
2. Place the foot over the column end so
received against the packing list. Table
the column fits into the square hole in the
assembly should be done on a clean
foot. The slotted holes in the foot should line
flat floor.
up with the four holes in the column end. If
not the foot needs to be removed and Note: When tightening the M8
screws, first twist in all four screws
repositioned at 90degrees
"finger tight", then tighten the screws
3. Attach the foot using four M8 x 20mm
one quarter turn at a time using
screws and four 8mm flat washers
a diagonal tightening pattern as
4. Thread leveling glide into the holes at shown in Detail A. Repeat the diagonal
pattern until all four screws are tight
the ends of the foot
(Figure 1 & Detail A).
5. Repeat steps 1 through 4 for the
second foot and column.
Assemble Feet To Columns
1. Set the column on end with the
smaller (inner) square tube on the
floor. The threaded holes visible
on the end of the column will
be in a rectangular (not square)
pattern (Figure 1).
Assembly of Table
2. Place the foot over the column
Tools Required: end so the column fits into the
square hole in the foot. The
· #2 Phillips Screwdriver
slotted holes in the foot should
· #3 Phillips Screwdriver
line up with the four holes in the
· 5mm Hex Key (provided)
column end. If not the foot needs
to be removed and repositioned at
90 degrees (Figure 1).
Note : Before discarding any packaging
confirm all components received against the
3. Attach the foot using four
packing list. Table assembly should be done
M8 x 20mm screws and four
on a clean flat floor.
8mm flat washers, tightening
each screw one quarter turn
Note : When tightening the M8 screws, first
at a time in a diagonal pattern
twist in all four screws "finger tight", then
until all four screws are tight
tighten the screws one quarter turn at a time
(Figure 1 & Detail A).
using a diagonal tightening pattern as shown
in Detail A. Repeat the diagonal pattern until
4. Thread leveling glides into the
all four screws are tight (Detail A & Figure 1).
holes at the ends of the foot
(Figure 1).
Note: If the roller foot option
was purchased, one foot will have
pre-assembled rollers.
Assemble Feet To Columns
5. Repeat steps 1 through 4 for
1. Set the column on end with the smaller
the second foot and column
(inner) square tube on the floor. The
(Figure 1).
threaded holes visible on the end of the
column will be in a rectangular (not square)
pattern (Figure 1) .
2. Place the foot over the column end so
the column fits into the square hole in the
foot. The slotted holes in the foot should line
up with the four holes in the column end. If
not the foot needs to be removed and
repositioned at 90degrees
(Figure 1) .
(Figure 1) .
(Figure 1) .
(Figure 1)
.