AMX FG1010-06 Quick Start Manual

Overview
DVI-D to RGBHV converters are available in two models: a standalone module and
an accessory board in an AF-10 (FIG. 1). This guide contains complete information for
the module. For the accessory board, see the AF-10 Quick Start Guide for instructions
on adding or replacing boards and for AF-10 specifications. All quick start guides are
on the AMX AutoPatch Software & Documentation CD and at www.amx.com.
DVI-D to RGBHV
AF-10 Board
DVI-D to RGBHV
Converter Module
(not to scale)
FIG. 1 Module FG1010-06
Product Specifications
Product Specifications
Approvals CE, UL, cUL
– +9 VDC, 500 mA wall transformer, 2.1 mm DC power jack
Power Module
Power – AF-10 120 VAC / 240 VAC
Humidity 0 to 90% non-condensing
Operational Temperature 32° - 110° F (0° - 43° C)
Dimensions – Module 5.22 in. (13.26 cm) depth
5.82 in. (14.78 cm) width
1.42 in. (3.61 cm) height without feet
– Approximately 1.5 lbs (0.68 kg)
Weight Module
Specification DVI-D 1.0 (single link)
DDC/EDID Support Provided by converter
HDCP Support No
Connectors DVI-I (supports DVI-D signal) and HD-15
Module Mounting Options
• Desktop – attach the rubber feet (included) on the bottom of the module.
• Rack Trays & Mounting Brackets – contact your AMX representative for details.
Installation
Typical System Setup
The DVI-I connector on the converter routes a DVI-D signal and accepts cable with
either DVI-D or DVI-I connector plugs. The module and the AF-10 board support the
eight resolutions listed in the table to the right above.
Destination monitor
Module (FG1010-06)
FIG. 2
System setup with converter module
Destination monitor
Boards (FG1040-485)
AF-10 (FG1040-10)
FIG. 3
System setup with AF-10 converter boards
AutoPatch
Supported Resolutions
The video card in the system must be set to one of the resolutions and its
corresponding refresh rate in the table below.
Supported Resolutions
640x480
800x600
1024x768
1152x864
1280x768
1280x960
1280x1024
1600x1200
AF-10 board FG1040-485
* Some monitors may not accept the maximum refresh rate.
** This refresh rate exceeds DVI specifications.
To change the Source PC's video card resolution/refresh settings on
Windows operating systems:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Installation
•
•
•
Module
To attach connectors:
1.
Source PC
FIG. 4
Source PC
2.

Quick Start Guide

DVI-D to RGBHV Converters
Resolution Refresh Rate*
120 Hz max.
120 Hz max.
120 Hz max.
100 Hz max.
85 Hz max.
85 Hz max.
85 Hz max.
75 Hz max.**
Minimize all applications on the Source PC.
Right click on the desktop.
Select Properties from the shortcut menu.
Select the Settings tab in the Display Properties dialog box.
Adjust the Screen area setting (resolution) to match one of the eight supported
resolutions listed in the table above.
Click Advanced.
Select the Monitor tab.
Adjust the Refresh Frequency, which is expressed in Hertz (see table above). If
the frequency setting is not located under the Monitor tab, try selecting other
available tabs.
Click Apply, and then click OK on each dialog box to exit.
Power down the PC.
Install the converter (see "Installation" below).
Reapply power to the PC.
Module – directions for attaching connectors are below
AF-10 Board – directions for attaching connectors are on the reverse
Pinouts – DVI-I (FIG. 6) and HD-15 (FIG. 7) connector pinouts are on the
reverse.
Insert the DVI-D and HD-15 cable connector plugs into the receptacles on the
module (FIG. 4).
Power cable
Attach DVI-D, HD-15, & power cable connectors
Plug the power cord into the power jack on the module and into the power
source.
DVI-I
receptacle
HD-15 cable DVI-D cable