AMX AF-10 Quick Start Manual

Overview
S-Video Distribution Amplifier (DA) boards are available as either standalone
distribution amplifier modules (left in FIG. 1) or as distribution amplifier accessory
boards for an AF-10 (right in FIG. 1). The S-Video DA Module has one input and four
outputs for a 1:4 distribution. S-Video DA boards have five S-Video connectors; either
one input and four outputs or five outputs that are paired with the 1:4 board to create a
1:9 distribution amplifier.
S-Video Module FG1010-70
(Not to scale)
FIG. 1 S-Video DA Module & AF-10 Boards
Product Specifications
General
Approvals
Power Consumption (max.) – Module
Power Connector – Module
Power – AF-10
Operational Temperature
Humidity
Dimensions – Module
Weight – Module
Connector Options
S-Video Specifications
Frequency Response
Signal to Noise Ratio (SNR) Vin = 0.7 V, 100% IRE
Level (max.)
Input:
Output:
Impedance
Input:
Output:
DC Offset Out (max.) Measured with 0 V on input
Product specifications below are specifically for AMX AutoPatch S-Video cables.
Video Bandwidth Specifications
Module FG1010-70
1:4 Board FG1040-452
+/-3 dB for 100 ft. (30.48 m)
+/-3 dB for 50 ft. (15.24 m)
+/-3 dB for 25 ft. (7.62 m)
+/-3 dB for 12 ft. (3.66 m)
+/-3 dB for 6 ft. (1.83 m)
+/-3 dB for 3 ft. (.91 m)
AutoPatch S-Video DA Modules & AF-10 Boards
1:4 S-Video AF-10 Board FG1040-452
5-out S-Video AF-10 Board FG1040-455
CE, UL, cUL
+9 VDC @ 500 mV
2.1 mm DC power jack
100 - 240 VAC single phase, 50 - 60 Hz
32° - 110° F (0° - 43° C)
0 to 90% non-condensing
5.22 in. (13.26 cm) depth
5.82 in. (14.78 cm) width
1.42 in. (3.61 cm) height w/out feet
Approx. 1.5 lb. (0.68 kg)
S-Video, Locking S-Video
+/- 3 dB, 50 MHz or better
+/- 1 dB, 15 MHz or better
-45 dB
+/- 1.75 V
+/- 1.75 V
75 ohms
75 ohms
+/- 20 mV
5-out Board FG1040-455
10 MHz 10 MHz
150 MHz 100 MHz
200 MHz 125 MHz
100 MHz 50 MHz
100 MHz 50 MHz
75 MHz 50 MHz
Installation
S-Video 1:4 Distribution Amplifier Module
Module Mounting Options
Desktop – Attach the rubber feet (included) on the bottom of the module.
Rack Trays & Mounting Brackets – contact your AMX representative for details.
Module System Setup
The S-Video DA Module has five S-Video connectors, one input and four outputs.
FIG. 2 Typical setup using S-Video DA Module
AF-10 with 1:4 & 5-out S-Video Distribution Amplifier Boards
Board System Set-up
S-Video DA 1:4 and 5-out boards are available for the AMX AutoPatch AF-10
Accessory Card Frame. The 1:4 board is built to use alone or in conjunction with the
5-out board. When using both, these boards must be installed in adjoining slot pairs,
with the 5-out board to the left of the 1:4 board for a 1:9 distribution.
5-out board
FIG. 3 Typical setup using S-Video DA boards in an AF-10
Attaching Cables
Note: AMX AutoPatch S-Video cables lock onto S-Video connectors. Standard
S-Video cables may be used, but will not lock.
To attach a locking S-Video connector:
1. Hold the connector at a slight angle to the right while pushing in or pull back on
the connector housing while pushing the connector in.
Connector housing
FIG. 4 Pull back on connector housing while pushing in
Quick Start Guide
1:4 board