Page 1
High Speed Burnisher Burnisher Operating instructions (ENG) MODELS: LB2000I 1.009-020.0 LB2000IA 1.009-021.0 UB2000F 1.009-062.0 LB2000 1.009-019.0 From Serial Number (Ref No1*) *See Serial Number Page in Spare Parts List or call manufacturer 86402450-A 06/23/15...
Machine Data Label Overview The High Speed Burnisher is a mains powered, portable floor burnisher intended for commercial use. The appliance can be fitted with a variety of pads to perform various floor care functions. The appliance employs active dust control, and automatically adjusted pad pressure. Warranty Registration Thank you for choosing our product.
How To Use This Manual This manual contains the following sections: The SAFETY section contains important information regarding hazardous or unsafe practices of the • How to Use This Manual machine. Levels of hazards are identified that could • Safety result in product damage, personal injury, or severe •...
Safety IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual.
Safety CONSIGNES DE SÉCURITÉ IMPORTANTES Lors de l'utilisation de cette machine, des précautions de base doivent toujours être prises, y compris les précautions suivantes : LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILISER CETTE MACHINE. Pour réduire le risque d'incendie, d'électrocution ou de blessure : N’utiliser cette machine qu’en intérieur.
Safety The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
Page 8
Safety Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions : DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques identifiés par les termes signalétiques –AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou entraîner la mort...
Safety Safety Labels NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. Emplacement De L'étiquette De Sécurité NOTE: REMARQUE: Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment, les étiquettes deviennent illisibles, contactez votre représentant autorisé...
Safety Grounding Instructions - 120v Grounding Pin THIS PRODUCT IS FOR COMMERCIAL USE ONLY. GROUNDING CONNECTION USING AN ADAPTOR Grounded Grounded Electrical: Outlet Box Adaptor Outlet In the USA this machine operates on a 15 amp FIGURE A nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine.
Safety Grounding Instructions - 230v THIS PRODUCT IS FOR COMMERCIAL USE ONLY. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Electrical: Check with a qualified electrician or service The amp, hertz, and voltage are listed on the data person if you are in doubt as to whether the outlet label found on each machine.
Motor 1.5 hp Transmission Direct drive from motor shaft. Pad speed 2000 rpm Electrical system: LB2000I, LB2000IA 230 volts, 50Hz LB2000, UB2000F 115 volts, 60Hz 75’ [22.9 m] Cable Switches Dual levers with safety lock. Pad Holder Æ20”...
Operations HANDLE ASSEMBLY HANDLE MOUNT BRACKET DECK ASSEMBLY Handle Installation The machine is shipped with handle unassembled. Follow these steps for installation: 1. Remove handle and deck assembly from carton. 2. Remove bolt (item 3), washers (item 2), and nut (item 1) from deck assembly. 3.
Operations Controls 2. Plug the machine into a wall outlet as described in the grounding instructions. 1. Safety Lock – Prevents unintended operation of 3. Release latch, lower the handle and move into the machine. position. 2. Switch Levers – Turns machine on/off. 4.
Maintenance Machine Troubleshooting PROBLEM CAUSE SOLUTION Tripped circuit breaker Reset Circuit breaker tripped in Check and reset building. Replace CAUTION: To reduce the risk of elec- trical shock, unplug the machine before opening fuse holder. Machine will not run Fuse in motor is blown Fuse will only open under extreme conditions.
Maintenance Service Schedule MAINTENANCE DAILY MONTHLY Check pad wear to prevent buildup of chemicals Check pad driver system for damage Check handles, switches, and knobs for damage Store with pad off the floor Check all bearings for noise Check skirt/bumpers for damage and replace as necessary Check overall performance of machine 86402450 Operators Manual - High Speed Burnisher (2000 Series)