Operating The Appliance; Switching The Hob On And Off; Setting A Hotplate; Chef's Recommendations - Siemens EX675LYV1E User Manual

1Operating the appliance

T his chapter explains how to set a hotplate. The table
O p e r a t i n g t h e a p p l i a n c e
shows heat settings and cooking times for various
meals.

Switching the hob on and off

Use the main switch to switch the hob on and off.
When you first switch on the appliance, you will be
prompted to set up your home network. The
will be lit dimly for a few seconds on the display panel.
To begin setting up the connection, touch the
sensor and proceed in accordance with the
D
information given in the section entitled ~ "Home
Connect".To exit initial set-up, touch any sensor.
To switch the hob on and off, touch the
audible signal will sound. The symbols for the cooking
zones and the functions available at this time will light
up.The hob is ready to use.
To switch the hob off, touch and hold the
until all indicators go out. The residual heat indicator will
remain lit until the cooking zones have cooled down
sufficiently.
Notes
If the appliance has not been connected to your
■
home network or the connection has been broken,
network connection initial set-up will be activated
whenever you switch on the hob.
The hob will automatically switch itself off if the
■
cooking zones have been switched off for a few
seconds.
The settings are stored for 4 seconds after the hob
■
has been switched off. If you switch the hob back on
during this time, the hob will operate using the
stored settings.

Setting a hotplate

Set the desired heat setting in the settings area.
Heat setting 1 = lowest setting.
Heat setting 9 = highest setting.
Every heat setting has an intermediate setting. This is
marked with .
†
The left-hand hotplates are set in the settings
Note:
area on the left and the right-hand hotplates are set in
the settings area on the right.
Selecting a hotplate and heat setting
The hob must be switched on.
Touch the and
" Ä
1.
hotplate.
The ‹ indicator gets brighter.
symbol
D
symbol. An
#
symbol
#
symbols for the required
THE EASIEST WAY TO SELF-IMPORT APPLIANCES DIRECT FROM EUROPE.
Swipe your finger over the relative settings area until
2.
the required heat setting lights up.
1.
The heat setting is set.
Changing the power level
Select the hotplate and set the desired power level in
the programming zone.
Switch off the hotplate
Select the hotplate and set it to
panel. The hotplate turns off and the residual heat
indicator appears.
Notes
If no pan has been placed on the hotplate, the
■
selected power level flashes. After a certain time has
elapsed, the hotplate switches off.
If a pan has been placed on the hotplate before
■
switching on the hob, it will be detected within
20 seconds of pressing the main switch and the
hotplate will be selected automatically. Once
detected, select the power level within the next
20 seconds or the hotplate will switch off.

Chef's recommendations

Recommendations
When heating up puree, cream soups and thick
■
sauces, stir occasionally.
Set heat setting 8 to 9 for preheating.
■
When cooking with the lid on, turn the heat setting
■
down as soon as steam escapes between the lid
and the cookware. Steam does not need to escape
for a good cooking result.
After cooking, keep the lid on the cookware until you
■
serve the food.
To cook with the pressure cooker, observe the
■
manufacturer's instructions.
Do not cook food for too long, otherwise the
■
nutrients will be lost. The kitchen clock can be used
to set the optimum cooking time.
For a more healthy cooking result, smoking oil
■
should be avoided.
To brown food, fry small portions in succession.
■
Cookware may reach high temperatures while the
■
food is cooking. We recommend that you use oven
gloves.
You can find recommendations for energy-efficient
■
cooking in section ~ "Environmental protection"
Operating the appliance
2.
in the programming
‹
en
11