Advertisement
Quick Links
Advertisement
Related Manuals for Yetter 2995 XFC
Summary of Contents for Yetter 2995 XFC
- Page 1 2995 XFC Fertilizer Coulter 2995 XCC Cutting Coulter OPERATORS MANUAL WITH PARTS IDENTIFICATION 2565-788_REV_B ● 11/2018 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com...
-
Page 2: Safety Alert Symbol
Important will WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. -
Page 3: Safety Precautions
SAFETY A brief description of signal words that may be used in this manual: CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices. WARNING: Denotes a specific potential hazard. DANGER: Denotes the most serious specific potential hazard. SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. -
Page 4: General Information
GENERAL INFORMATION... - Page 5 GENERAL INFORMATION...
-
Page 8: Maintenance
MAINTENANCE • After a few hours use, check all bolts and setscrews for tightness. • After using a few hours, check for loose hardware, re-tighten as needed. • After a few days use, check coulter hubs for loose bearings. There should be no end play in the hub bearings to allow it to wobble. - Page 9 ASSEMBLY INSTRUCTIONS STEP 1. Install shank to the coulter assembly.
- Page 10 ASSEMBLY INSTRUCTIONS STEP 2. Install roll pin to the shank.
- Page 11 ASSEMBLY INSTRUCTIONS STEP 3. Attach the blade to the coulter assembly using the 4) ½” – 20 X 1” Hex Head Bolts.
- Page 12 ASSEMBLY INSTRUCTIONS STEP 4. Attach the toolbar clamp to the frame.
- Page 13 ASSEMBLY INSTRUCTIONS STEP 5. Loosely assemble the set screws and lock nuts to the toolbar clamp.
- Page 14 ASSEMBLY INSTRUCTIONS STEP 6. Slide shank into the toolbar clamp. Install roll pin to the shank.
- Page 15 ASSEMBLY INSTRUCTIONS STEP 7. Adjust coulter shank up or down as needed to securely tighten 2) set screws. STEP 8. If using fertilizer, install the injector or knife as shown in the parts identification section of this manual.
- Page 16 PARTS IDENTIFICATION...
- Page 17 PARTS IDENTIFICATION...
- Page 18 PARTS IDENTIFICATION COULTER ASSEMBLY 2995-197-RH...
- Page 19 PARTS IDENTIFICATION COULTER ASSEMBLY LH 2995-197-LH...
- Page 20 PARTS IDENTIFICATION...
- Page 21 PARTS IDENTIFICATION COULTER ASSEMBLY 2995-153...
- Page 22 PARTS IDENTIFICATION...
- Page 23 PARTS IDENTIFICATION 2995-149...
- Page 24 PARTS IDENTIFICATION 2995-138...
- Page 25 PARTS IDENTIFICATION...
- Page 26 PARTS IDENTIFICATION...
- Page 27 PARTS IDENTIFICATION...
- Page 28 PARTS IDENTIFICATION...
- Page 29 PARTS IDENTIFICATION...
- Page 30 PARTS IDENTIFICATION...
- Page 31 PARTS IDENTIFICATION...
-
Page 32: Troubleshooting
TROUBLESHOOTING... - Page 33 NOTES:...
- Page 34 NOTES:...
- Page 35 NOTES:...
- Page 36 South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa. So, when you buy Yetter products . . .you’re buying a name that’s recognized. A name that’s known and respected. A name that’s become a part of American agriculture and has become synonymous with quality and satisfaction in the field of conservation tillage.