Advertisement
Quick Links
2995 XFC Fertilizer Coulter
2995 XCC Cutting Coulter
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website:
www.yetterco.com
E-mail:
info@yetterco.com
OPERATORS MANUAL
WITH PARTS IDENTIFICATION
2565-788_REV_F ● 08/2024
Advertisement
Related Manuals for Yetter 2995 XFC
Summary of Contents for Yetter 2995 XFC
- Page 1 2995 XFC Fertilizer Coulter 2995 XCC Cutting Coulter OPERATORS MANUAL WITH PARTS IDENTIFICATION 2565-788_REV_F ● 08/2024 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com...
- Page 2 It is the user’s responsibility to deliver his machine to the Yetter dealer who sold him the product for service or replacement of defective parts, which are covered by the warranty policy.
- Page 3 SAFETY PRECAUTIONS A brief description of signal words that may be used in this manual: DANGER: Indicates an imminently hazardous situation which, if not avoided “will” result in death or serious injury. This signal word is to be limited to the most extreme situations. WARNING: Indicates a potentially hazardous situation which, if not avoided, “could”...
- Page 4 GENERAL INFORMATION...
- Page 5 GENERAL INFORMATION...
- Page 8 MAINTENANCE • After a few hours use, check all bolts and setscrews for tightness. • After using a few hours, check for loose hardware, re-tighten as needed. • After a few days use, check coulter hubs for loose bearings. There should be no end play in the hub bearings to allow it to wobble.
- Page 9 ASSEMBLY INSTRUCTIONS STEP 1. Install shank to the coulter assembly.
- Page 10 ASSEMBLY INSTRUCTIONS STEP 2. Install roll pin to the shank.
- Page 11 ASSEMBLY INSTRUCTIONS STEP 3. Attach the blade to the coulter assembly using the 4) ½” – 20 X 1” Hex Head Bolts.
- Page 12 ASSEMBLY INSTRUCTIONS STEP 4. Attach the toolbar clamp to the frame.
- Page 13 ASSEMBLY INSTRUCTIONS STEP 5. Loosely assemble the set screws and lock nuts to the toolbar clamp.
- Page 14 ASSEMBLY INSTRUCTIONS STEP 6. Slide shank into the toolbar clamp. Install roll pin to the shank.
- Page 15 ASSEMBLY INSTRUCTIONS STEP 7. Adjust coulter shank up or down as needed to securely tighten 2) set screws. STEP 8. If using fertilizer, install the 2995-083 injector or 2995-084 knife as shown in the parts identification section of this manual. When installing the 2995-084 knife kit, bend the fertilizer tube slightly enough to allow clearance for the 2502-367 ½...
- Page 16 PARTS IDENTIFICATION...
- Page 17 PARTS IDENTIFICATION...
- Page 18 1-17/64 ID X 2-1/4 OD X 10 GAUGE MACHINE WASHER 2531-109 5/32 X 1-1/4 COTTER PIN 2531-125 ¼ X 1-3/4 COTTER PIN 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP 2565-162 YETTER DECAL 2565-832 GREASE DAILY DECAL 2986-405 SPRING BUSHING 2995-138 633 HUB ASSEMBLY 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP...
- Page 19 1-17/64 ID X 2-1/4 OD X 10 GAUGE MACHINE WASHER 2531-109 5/32 X 1-1/4 COTTER PIN 2531-125 ¼ X 1-3/4 COTTER PIN 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP 2565-162 YETTER DECAL 2565-832 GREASE DAILY DECAL 2986-405 SPRING BUSHING 2995-138 633 HUB ASSEMBLY 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP...
- Page 20 PARTS IDENTIFICATION...
- Page 21 1-17/64 ID X 2-1/4 OD X 10 GAUGE MACHINE WASHER 2531-109 5/32 X 1-1/4 COTTER PIN 2531-125 ¼ X 1-3/4 COTTER PIN 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP 2565-162 YETTER DECAL 2565-832 GREASE DAILY DECAL 2986-405 SPRING BUSHING 2995-138 633 HUB ASSEMBLY 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP...
- Page 22 PARTS IDENTIFICATION...
- Page 23 1-17/64 ID X 2-1/4 OD X 10 GAUGE MACHINE WASHER 2531-109 5/32 X 1-1/4 COTTER PIN 2531-125 ¼ X 1-3/4 COTTER PIN 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP 2565-162 YETTER DECAL 2565-832 GREASE DAILY DECAL 2986-405 SPRING BUSHING 2995-138 633 HUB ASSEMBLY 2533-110 ¼-28 LUBE FITTING STRAIGHT SELF-TAP...
- Page 24 PARTS IDENTIFICATION 2995-138...
- Page 25 PARTS IDENTIFICATION...
- Page 26 PARTS IDENTIFICATION...
- Page 27 PARTS IDENTIFICATION...
- Page 28 PARTS IDENTIFICATION...
- Page 29 PARTS IDENTIFICATION...
- Page 30 PARTS IDENTIFICATION...
- Page 31 TROUBLESHOOTING...
- Page 32 South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa. So, when you buy Yetter products . . .you’re buying a name that’s recognized. A name that’s known and respected. A name that’s become a part of American agriculture and has become synonymous with quality and satisfaction in the field of conservation tillage.
Need help?
Do you have a question about the 2995 XFC and is the answer not in the manual?
Questions and answers