Allegion LCN 2210 Series Installation Instructions

Fig. 1
Fig. 1
*27297*
27297
Door Closers
Fig. 1
1a

Make sure hand of closer matches hand of door.

Remove finish plates. Hand of closer is printed on
the mounting plate label. Hand of closer cannot be
reversed. See diagram above to determine hand of
FINISH PLATE
TORX SCREWS
door.
ARM SHAFT
1b Prepare and mortise door & frame per template on pg.
FINISH PLATE
FINISH PLATE
TORX SCREWS
4.
TRACK
TORX SCREWS
TORX
ARM SHAFT
SCREWS
ARM SHAFT
SCREW
1c

Install closer in prepared headframe, as shown in Fig.

FINISH PLATE
TORX SCREWS
1, with spring tube pointing away from hinge. Fasten
TRACK
ARM SHAFT
TRACK
TORX
SCREW
mounting plate to jamb with 1/4 - 20 x 5/8 PHMS
TRACK
TORX
SCREWS
TRACK
SCREWS
provided.
TORX
SCREWS
1d Install track in door. Roller access hole must be toward
TRACK
TRACK
TRACK
latch edge of door, as shown in Fig. 1. Fasten with 1/4
- 20 x 1/2 TORX MS provided.
1e Connect arm assembly to track by placing plastic roller
at end of arm into the roller access hole in track. See
Fig. 1. Let arm assembly rest on top of installed track.
1f

To attach arm to closer:

a. Open door out of working area.
b. With a 3/32" hex wrench, turn latch & main speed
regulating screws all the way in (clockwise). See Fig. 2. DO
NOT FORCE SCREWS.
Fig. 2
c. Using an adjustable wrench, rotate door closer shaft
approximately 90°. See Fig. 3. (R.H. - clockwise / L.H. -
counterclockwise).
Fig. 2
LATCH MAIN
SPEED SPEED
LATCH
SPEED
HOW TO TELL HAND OF DOOR
LATCH MAIN
LATCH
LEFT RIGHT
SPEED SPEED
HAND HAND
SPEED
DOOR
DOOR
HOW TO TELL HAND OF DOOR
LEFT
HAND
HOW TO TELL HAND OF DOOR
DOOR
HOW TO TELL HAND OF DOOR
LEFT
LEFT
HAND
HAND
DOOR
DOOR
2210 Series
CLOSER
ASSEMBLY
MOUNTING
SCREWS
FINISH
PLATE
SCREW
ARM
ASSEMBLY
ROLLER
ACCESS
HOLE
SCREW
Fig. 2
Fig. 2
BACK
CHECK
BACK
MAIN
CHECK
SPEED
BACK
BACK
MAIN
CHECK
CHECK
SPEED
RIGHT
HAND
DOOR
RIGHT
RIGHT
HAND
HAND
DOOR
DOOR
CLOSER
ASSEMBLY
MOUNTING
SCREWS
CLOSER
ASSEMBLY CLOSER
FINISH
ASSEMBLY
PLATE
MOUNTING
MOUNTING
SCREWS
SCREWS ARM
ASSEMBLY
FINISH
Fig. 1
PLATE FINISH
ROLLER
PLATE
ACCESS
ARM
HOLE
ARM
ASSEMBLY
ASSEMBLY
ROLLER
ROLLER
ACCESS
ACCESS
HOLE
HOLE
FINISH PLATE
TORX SCREWS
ARM SHAFT
TRACK
TORX
SCREWS
TRACK
Fig. 3
90°
LATCH
SPEED
HOW TO TELL HAND OF DOOR
LEFT
HAND
DOOR
TM
SCREW
Fig. 3
Fig. 3
Fig. 3
90°
Fig. 2
Customer Service
1-877-671-7011 www.allegion.com/us
BACK
MAIN
CHECK
SPEED
RIGHT
HAND
DOOR
Installation Instructions
CLOSER
ASSEMBLY
MOUNTING
SCREWS
FINISH
PLATE
ARM
ASSEMBLY
ROLLER
ACCESS
HOLE
90°
90°
© Allegion 2014
Printed in U.S.A.
27297 Rev. 03/14-f