Download Print this page

Advertisement

TM
OPERATING MANUAL
BEDIENUNGSANLEITUNG
MODE D'EMPLOI
MANUAL DE FUNCIONAMIENTO
MANUALE DI ISTRUZIONI
ΕΓΧΕΙΡΙ∆ΙΟ ΛΕΙΤΟΥΡΓΙΑΣ
O
M
PERATING
ANUAL
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
AIR CONDITIONER
MANUAL DE INSTRUÇÕES
REMOTE CONTROLLER
(WIRED TYPE)
Remote Control Unit
UTB- LB
KEEP THIS OPERATION MANUAL
FOR FUTURE REFERENCE
FUJITSU GENERAL LIMITED
P/N9372112014

Advertisement

   Related Manuals for Fujitsu Airstage UTB- LB Series

   Summary of Contents for Fujitsu Airstage UTB- LB Series

  • Page 1

    MODE D’EMPLOI MANUAL DE FUNCIONAMIENTO MANUALE DI ISTRUZIONI ΕΓΧΕΙΡΙ∆ΙΟ ΛΕΙΤΟΥΡΓΙΑΣ PERATING ANUAL РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ AIR CONDITIONER MANUAL DE INSTRUÇÕES REMOTE CONTROLLER (WIRED TYPE) Remote Control Unit UTB- LB KEEP THIS OPERATION MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED P/N9372112014...

  • Page 2: Table Of Contents

    CONTENTS SAFETY PRECAUTIONS............1 TIMER OPERATION (Weekly timer) ........5 NAME OF PARTS ..............1 OPERATING TIPS ..............6 PREPARATORY OPERATION ........... 2 ERRORS AND SELF-DIAGNOSIS ........... 7 OPERATION ................2 TROUBLESHOOTING .............. 7 TIMER OPERATION (ON timer/OFF timer/Weekly timer) ..3 SPECIFICATIONS ..............

  • Page 3: Preparatory Operation

    PREPARATORY OPERATION Instructions relating to heating are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Set the current day and time Press for 3 seconds. Select the number that corresponds to the current day indicated by a code from 1 to 7.

  • Page 4: Timer Operation (on Timer/off Timer/weekly Timer)

    TIMER OPERATION (ON timer/OFF timer/Weekly timer) Instructions relating to heating are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). The timer function cannot be used when the remote controller is a slave unit. (For information concerning the slave unit, refer to the INSTALLATION INSTRUCTION SHEET of the remote controller.) To set the ON/OFF timer Select either “OFF TIMER”...

  • Page 5

    To start/stop the WEEKLY timer operation To start To stop The current time Select “NON STOP,” “OFF TIMER” or “ON TIMER”. Next scheduled ON or OFF time Select (If the air conditioner is running, the day display is replaced by the temperature display.) To review the WEEKLY timer settings * Press the START/STOP button to stop the air conditioner, and then proceed as follows.

  • Page 6: Timer Operation (weekly Timer)

    TIMER OPERATION (Weekly timer) Instructions relating to heating are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). To change the selected time settings * Press the START/STOP button to stop the air conditioner, and then proceed as follows. Perform steps in “To set the WEEKLY timer.”...

  • Page 7: Operating Tips

    NOTES (1) In the following cases, cancel the set time prior to making the required amendments. Temporary overlap 1.If you want to change the ON time to a time that is later than WEEKLY 1 WEEKLY 2 Time the currently set OFF time. Change 2.If the change would cause a temporary overlap between the WEEKLY 1...

  • Page 8: Errors And Self-diagnosis

    Cooling/heating priority (HEAT PUMP MODEL only) Weekly timer • If another indoor unit in the same system is already oper- • Set different operating times for each day of the week. ating in the cooling mode or dry mode, heating mode set- •...

  • Page 9: Specifications

    Before requesting service, perform the following checks: Symptom CAUSE and ACTION See Page G If the unit is stopped and then immediately started again, the com- NORMAL Doesn’t operate immedi- FUNCTION ately: pressor will not operate for about 3 minutes, in order to prevent fuse blowouts.

Comments to this Manuals

Symbols: 0
Latest comments: