Advertisement
FZ-SFC/SF/SPC/SP
Model
SMALL DIGITAL CAMERA FOR
MODEL FZ VISUAL INSPECTION SYSTEM
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describ es precautions req uired in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acq uire sufficient kno wledge of the product. For your con-
venience, keep the sheet at your disposal.
TRACEABILITY INFORMATION:
Representative in EU
Manufacturer
Omron Europe B.V.
Omron Corporation,
Wegalaan 67-69
Sensing Devices & Components Div.H.Q.,
2132 JD Hoofddorp
Application Sensors Division
The Netherlands
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 JAPAN
NOTICE:
This product meets CISPR11 class A. The intended use of this product
is in an industrial environment only.
©
OMRON Corporation
2008
All Rights Reserved.
PRECAUTIONS ON SAFETY
Meaning of Alert Symbols
Indicates a potentially hazardous situation which, if
not avoided, will result in minor or moderate injury,
WARNING
or may result in serious injury or death. Additionally
there may be significant property damage.
Indicates a potentially hazardous situation which, if
CAUTION
not avoided, may result in minor or moderate injury
or in property damage.
Alert statements
WARNING
This product is not designed or rated for ensuring
safety of persons. Do not use it for such purposes.
It is likely to lose one's sight unusually.Please do not
look at the sun light directly with the lens unit.
CAUTION
Please do not put it on the place where direct sunshine
tries the lens with the lens removed from the camera.
A fire might occur unusually.
PRECAUTIONS FOR SAFE USE
Be sure to respect following items for safety.
(1) Installation Site
Do not install the product in locations subjected to the following
conditions:
･ Ambient temperature outside the rating
･ Rapid temperature fluctuations (causing condensation)
･ Relative humidity outside the range of 35 to 85%
･ Presence of corrosive or flammable gases
･ Presence of dust, salt, or metallic particles
･ Direct vibration or shock
･ Reflection of intense light (such as other laser beams or electric
arc-welding machines)
･ Direct sunlight or near heaters
■Use of lens and photograph ring
(All models)
(1) Mount of lens as shown in the figure below, and screw in
to the inner of the camera mount. Put the photograph ring
between the camera head and the lens after referring to an
optical diagram when you want to use it in the narrowness
view and the short distance.
(2) Loosen the lens and the photographing ring to the position
in which the focus of the image is suitable, and fix firmly
with the lens fixation ring.
(3) Rotate a knob after adjusting the brightness of the image
by the disphragm adjustment knob, detain temporarily,
and fix firmly with the fixed screw of the other side.
Drawing out dimension of lens
Diaphragm adjustment knob
(0.7mm to 2.7mm)
Diaphragm look screw
Lens fixation ring
Diaphragm
Drawing out dimension of lens
adjustment knob
(0mm to 2.0mm)
Lens fixation ring
Diaphragm look screw
※Please use the draw out dimension of lens within the
above-mentioned range.The lens and the photographing
ring might come off according to the environment of use
when used by the dimension outside the range.
･ Water, oil, or chemical fumes or spray
･ Strong magnetic or electric field
･ Near high-voltage eqipment or power eqipment
(2) Handling the Camera
In the installation, tighten the screw, the lens, and the
photograph ring surely.
The Camera amplifier case is connected to the 0V line in the internal circuits.
Observe the following precautions to prevent noise interference.
･ Do not ground the Camera.
･ Please use the plinth and the mounting bracket when you set it up.
(3) Others
･
Do not use unspecified camera cable and a strobe controller
other than those that specified in this manual with the FZ
controller. Connection with unspecified camera cable and/or
strobe controller may malfunction at the worst case.
･ If you do not use the enhancing connector on the back of the camera
amplifier, do not remove the cap that is attached to the connector.
･ Do not attempt to dismantle, repair, or modify the main body.
･ If you suspect an error or malfunction, stop using the Controller
immediately, turn OFF the power supply, and consult your
OMRON representative.
･ Dispose of FZ-SC5M/S5M components as industrial waste.
PRECAUTIONS FOR CORRECT USE
Please observe the following precautions to prevent failure to operate,
malfunction, or undesirable effect.
(1) Connecting Cables
･ Be sure to turn off the power before connecting or
disconnecting the cables.The camera might break when the
power supply detaches it while turned on.
(2) Optical axis of the Camera.
･ The center of the optical axis varies with the camera used.
Therefore, when installing the camera, always check the center
of the image displayed on the monitor.
(3) Maintenance
･ If large dust particles adhere to the CCD, use a blowerbrush
(used to clean camera lenses) to blow them off. Do not blow
the dust particles with your mouth.
･ Do not use thinners, benzene, acetone, or kerosene to clean Camera.
■Accessories
Main unit, instruction sheet(this manual), mounting bracket
(only FZ-SFC/SF), four screws(M2×4 only FZ-SFC/SF)
■Specifications
Small camera
▲General specifications
Item
FZ-SFC/SF
FZ-SPC/SP
Pencil type
shape
Flat type
Power
3.4W max.(13V DC,0.26A max.)
consumption
10 to 150Hz: half-amplitude: 0.35mm:
Vibration
2
(maximum acceleration: 50m/s
resistance
10 times each in X, Y, and Z directions for 8 min
2
Shock resistance 150m/s
;
Shock
3 times each in 6 directions
resistance
(up/down, left/right, forward/backward)
℃(camera head)
Operating: 0 to 50
(with no icing nor condensation)
Ambient
℃(camera amplifier)
Operating: 0 to 45
Temperature
(with no icing nor condensation)
Storage: -25 to 65
℃
(with no icing nor condensation)
Ambient
Operating and storage: 35% to 85%
humidity
(with no condensation)
Ambient
No corrosive gases
environment
Degree of
IEC60529 IP20 (in-panel)
protection
Cover: Galvanized sheet iron
Materials/Weight
Case: Aluminum die cast alloy (ADC-12)
(Camera amplifier)
Base: polycarbonate ABS
60g （including base）
Case: Aluminum alloy (A5056)
Case: Aluminum alloy (A5056)
Materials/Weight
Bracket: MC nylon
Base: PC / Glass fiber
(Camera head)
Cap: Silicon rubber
Cap: Silicon rubber
70g （including bracket）
70g （including base）
■Dimensions
●
Camera
head(FZ-SPC/SP)
6
12
2-4.5Dia.
MOUNTING SCREW HOLES
M10.5
9
2-M3 DEPTH 4
8-M1.7 DEPTH 1.5
4-M1.7 DEPTH 1.5
3Dia.
16PIN ROUND CONNECTOR
12.5Dia.
（Unit ： mm）
●P
hotograph ring
（ FZ-LESR optional）
3
5
3
10
3
PHOTOGRAPH RING
PHOTOGRAPH RING
PHOTOGRAPH RING
5mm
10mm
15mm
（Unit ： mm）
■Optical diagram
Select the lens and the photograph ring referring to the table below.
WD （mm）
10000
1000
t5
t10
100
t15
t20
t45
t40
t35
t30
t25
t50
t5
t55
t60
t10
t15
t20
10
1
10
Performance specifications
▲
Item
FZ-SFC/SPC
Picture element
1/3-inch color CCD
Transmission mode
Interline reading all pixels
Effective pixels
Pixel size
7.4(µm)×7.4(µm)(Square pixel)
Scanning method
Non-interlace mode
Frame rate
Number of lines to be
12 lines to 480 lines
read
Synchronization
Video output
Gain
Shutter speed
Special mount (M10.5 P0.5)
Lens mounting
Small lens /
Photograph ring
Item
FZ-LES3
FZ-LES6
FZ-LES16
Focal length
3mm
6mm
16mm
Aperture
F2.0
Lens: Optical glass
Materials
Outline: Aluminum alloy(CB156)
Weight
Approx. 5g
■Changing the base mount position of
camera amplifier(All models)
The camera base attached to the bottom of the camera
amplifier
can also be attached to the another side of the
camera
amplifier
.Remove the four screws(M2×7) from the
base and re-attach the base to the another side of the camera
.(Recommended screw tightening torque ： 0.32N･m)
amplifier
When the plinth is attached in the top side and the side,
mount it by three mounting screws.
■Changing the base mount position of
camera head(FZ-SPC/SP)
The camera base attached to the bottom of the camera
can also be attached to the another side of the camera
head
),
.Remove the four screws(M1.4×5) from the base and
head
re-attach the base to the another side of the camera
.(Recommended screw tightening torque ： 0.15N･m)
head
The distance from the lens mount to plinth must note the
change from the installation of top side or the bottom
when you install it in side respect of plinth.
■Use of mounting bracket for camera head (FZ-SFC/SF)
The mounting bracket of the FZ-SFC/SF attachment is fixed
by screw(M2×4 Four) that is attached to camera head in the
direction of figure below.
(Recommended screw tightening torque ： 0.1N･m)
●
Camera
head(FZ-SFC/SF)
2-M4
8
9
MOUNTING SCREW HOLES1
16.9
3.4
13.5
34
26
3
4-4.3Dia.
3Dia.
16PIN ROUND CONNECTOR
●
（FZ-LES□□ optional）
Small lens
15
DIAPHRAGM
L
ADJUSTMENT KNOB
DIAPHRAGM LOOK SCREW(M1.4)
（Unit ： mm）
FZ-LES30
FZ-LES16
t0
FZ-LES6
t0
FZ-LES3
t0
t0
WD
Y view
100
1000
Y view （mm）
Please mount it as shown in the figure below.
FZ-SF/SP
Bottom installation
1/3-inch monochrome CCD
659(H)×494(V)
80fps
Internal Sync.
Spacer must use the length of 11mm or more to prevent
*
Digital (10 bits)
camera head from coming in contact with metallic side.
-6dB to + 24dB
Side installation
1/10 to 1/50000s
FZ-LES30
FZ-LESR
30mm
−
F3.4
−
Aluminum alloy
(A5056)
Approx. 6g
Approx. 4g
■Connection of camera head and camera amplifier
Please do insert the front connector of camera amplifier
with connector of camera head, turn the ring, and fix firmly.
The model and the serial number are confirmed.
Confirm the model and serial number of the camera
amplifier and camera head is same, when connecting it.
When the camera head and the camera amplifier of a
different model and the serial number are connected, it
doesn't operate normally.
Connection of camera amplifier and camera cable
(1) Using the Camera cable FZ-VS□□(sold separately),
connect the connector on the back of the camera amplifier
and the camera connector on Controller FZ series.
Name plate
*The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so,
make sure that the end bearing a name plate is connected to the
Controller.
●
Camera
amplifier(All models)
2-4.3Dia.
26±0.1
4-M4
3-M2 DEPTH 3.0
MOUNTING SCREW HOLES2
9.2(FROM CCD SURFACE)
28
17
24
2-M4 DEPTH 5.5
19±0.1
12.5Dia.
（Unit ： mm）
MOUNTING SCREW HOLES
Model
L
16.4
FZ-LES3
FZ-LES6
19.7
THE PRODUCTS CONTAINED IN THIS SHEET ARE NOT SAFETY RATED.
FZ-LES16
23.1
THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY
FZ-LES30
25.5
COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES.
Please refer to separate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or
regulations that apply to the combination of the products in the customer's
application or use of the product.
Take all necessary steps to determine the suitability of the product for the
systems, machines, and equipment with which it will be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
Camera head
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
Photograph
EQUIPMENT OR SYSTEM.
ring
See also Product catalog for Warranty and Limitation of Liability.
Lens
EUROPE
OMRON EUROPE B.V. Sensor Business Unit
Carl-Benz Str.4, D-71154 Nufringen Germany
Phone:49-7032-811-0 Fax: 49-7032-811-199
NORTH AMERICA
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,IL 60173-5302 U.S.A
Phone:1-847-843-7900 Telephone Consultation
1-800-55-OMRON Fax : 1-847-843-7787
ASIA-PACIFIC
OMRON ASIA PACIFIC PTE LTD
83 Clemenceau Avenue,#11-01 UE Square,Singapore 239920
Phone : 65-6-835-3011 /Fax :65-6-835-2711
OMRON Corporation
Spacer
Model
Serial number
Enhancing connector
Camera cable
FZ-VS□□
Camera cable
connector
Camera amplifier
FZ-SFC/SF/SPC/SP
11.5
22
43.5
37
(6.5)
11.5
22
(6.5)
7.5
(8.8Dia.)
3-M2 DEPTH 3.0
7.5 9.5
9.5
2.5
33.5
1/4"-20UNC DEPTH 5.5
2-4.5Dia.
（Unit ： mm）
Suitability for Use
n
Advertisement
