Ozito ASG-GFK Instruction Manual

Ozito ASG-GFK Instruction Manual

Gravity feed spray gun 100-190 ml/min, touch-up gravity feed spray gun 70-110 ml/min

Advertisement

Quick Links

GRAVITY FEED
SPRAY GUN
100-190 ml/min
INSTRUCTION MANUAL
SPECIFICATIONS
Working Air Pressure:
43psi (3Bar)
Max Air Pressure:
87psi (6Bar)
Air Consumption:
141-283L/min (5-10cfm)
Nozzle Size:
ø1.4mm
Spray Width:
40-70mm
Flow Rate:
100-190ml/min
Feed Type:
Gravity
Paint Pot Size:
600ml
Air Inlet:
1/4" BSP
ozito.com.au
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO
Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
WARRANTY
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes
consumable parts.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WHAT'S IN THE BOX
Spray Gun
Paint Pot
Filter
ASG-GFK
0414

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ASG-GFK and is the answer not in the manual?

Questions and answers

Summary of Contents for Ozito ASG-GFK

  • Page 1 600ml Air Inlet: 1/4” BSP ozito.com.au Filter ASG-GFK WARRANTY IN ORDER TO MAKE A CLAIM UNDER THIS The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law. WARRANTY YOU MUST RETURN THE PRODUCT...
  • Page 2: Know Your Product

    KNOW YOUR PRODUCT SETUP & PREPARATION GRAVITY FEED SPRAY GUN 1. ASSEMBLY 1 Nozzle 6 Air Regulator Valve 2 Nozzle Collar 7 Air Inlet WARNING! ENSURE THE TOOL IS DISCONNECTED FROM 3 Variable Trigger 8 Fluid Adjustment Dial THE AIR SUPPLY BEFORE PERFORMING ANY OF THE FOLLOWING OPERATIONS.
  • Page 3: Operation

    OPERATION 3. ADJUSTING THE SPRAY GUN 2. PREPARATION Variable Trigger NOTE: FOR BEST RESULTS, SURFACE PREPARATION AND PAINT THINNING ARE THE TWO MOST IMPORTANT AREAS. ENSURE 1 Squeeze the variable 2 Release the variable ALL SURFACES ARE FREE OF DUST, DIRT AND GREASE. trigger to start spraying.
  • Page 4 NOTE: After each use it is essential that the spray gun is cleaned thoroughly. Failure to do so will likely cause blockages which will prevent the tool from working. FAILURE TO CLEAN THE TOOL WILL VOID THE WARRANTY. ASG-GFK...
  • Page 5: Cleaning Procedure

    Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse. For further information, or any parts not listed here, visit www.ozito.com.au or contact Ozito Customer Service: Australia 1800 069 486 New Zealand 0508 069 486 E-mail: enquires@ozito.com.au...
  • Page 6: Spray Gun Safety Warnings

    GENERAL AIR TOOL SAFETY WARNINGS WARNING! WARNING! Read all safety warnings and all instructions. Failure to follow the warnings In the event that an air line is cut or broken, the air supply must be turned off at the and instructions may result in electric shock, fire and/or serious injury. compressor.
  • Page 7: Warranty

    Paint Pot Size: 100ml Air Inlet: 1/4” BSP ozito.com.au ASG-GFK WARRANTY IN ORDER TO MAKE A CLAIM UNDER THIS The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law.
  • Page 8 KNOW YOUR PRODUCT SETUP & PREPARATION GRAVITY FEED SPRAY GUN 1. ASSEMBLY 1 Nozzle 5 Air Regulator Valve 2 Nozzle Collar 6 Air Inlet WARNING! ENSURE THE TOOL IS DISCONNECTED FROM 3 Variable Trigger 7 Fluid Adjustment Dial THE AIR SUPPLY BEFORE PERFORMING ANY OF THE FOLLOWING OPERATIONS.
  • Page 9 OPERATION 3. ADJUSTING THE SPRAY GUN 2. PREPARATION Variable Trigger NOTE: FOR BEST RESULTS, SURFACE PREPARATION AND PAINT THINNING ARE THE TWO MOST IMPORTANT AREAS. ENSURE 1 Squeeze the variable 2 Release the variable ALL SURFACES ARE FREE OF DUST, DIRT AND GREASE. trigger to start spraying.
  • Page 10 NOTE: After each use it is essential that the spray gun is cleaned thoroughly. Failure to do so will likely cause blockages which will prevent the tool from working. FAILURE TO CLEAN THE TOOL WILL VOID THE WARRANTY. ASG-GFK...
  • Page 11 Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse. For further information, or any parts not listed here, visit www.ozito.com.au or contact Ozito Customer Service: Australia 1800 069 486 New Zealand 0508 069 486 E-mail: enquires@ozito.com.au...
  • Page 12 GENERAL AIR TOOL SAFETY WARNINGS WARNING! WARNING! Read all safety warnings and all instructions. Failure to follow the warnings In the event that an air line is cut or broken, the air supply must be turned off at the and instructions may result in electric shock, fire and/or serious injury. compressor.

Table of Contents