The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool" in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Page 6
GENERAL POWER TOOL SAFETY WARNINGS (cont.) d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
ADDITIONAL SAFETY INSTRUCTIONS FOR SPRAY GUNS Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live“...
ASSEMBLY Turn the Quick release knobs (3) on both sides of Fig. 1 the spray gun to the “Unlock” position. Note: Ensure the paint head and spray gun body are aligned correctly for proper fitting (Fig.1) Fully insert the paint head into the spray gun body Fig.
Page 9
PREPARATION (cont.) Thinning Thinning is particularly important when spraying. Most paints are supplied ready for brush application and need to be diluted sufficiently for spraying purposes. Follow the manufacturers guide for thinning in conjunction with a spray gun. If in doubt please consult the manufacturer of the paint.
OPERATION Aligning the Suction Tube WARNING! Ensure the spray gun is disconnected from the mains power supply before removing the paint pot. Adjust the suction tube accordingly. It should be possible to spray the contents of the container leaving hardly any material left in the container Unscrew the Paint pot (7) from the spray gun, rotate anti-clockwise and pull away from the body of the spray gun Spraying with horizontal objects...
Page 11
OPERATION (cont.) Choice of spraying patterns (Fig. 7) Fig. 7 A = vertical fan – for horizontal surfaces B = horizontal fan – for vertical surfaces. C = round fan – for corners, edges and other hard to access places. Adjusting the required spray pattern (Fig.
Page 12
OPERATION (cont.) If coating material builds up on the nozzle (2) and Fig. 11 Air cap nut air cap (1) (Fig.11) Remove the air cap nut and air cap (1). Clean both parts and around nozzle (2) with solvent or water using a stiff brush. If the nozzle (2) becomes blocked it can be removed by using a 9mm open ended spanner, carefully unscrew from the paint head.
Page 13
CLEANING WARNING! Always ensure that the Spray Gun is disconnected from the mains power supply before making any adjustment or cleaning. Clean After Every Use After every use it is essential that you clean the gun thoroughly. This will prevent any blockages occurring and provide reliable performance when you next come to use it.
Page 14
WARNING! Always ensure that the Spray Gun is switched off and unplugged from the power supply before making any adjustment. Filters can be purchased in packs of 2 (Ozito p/n SPSPG300-03) and are available from your local Bunnings Warehouse. Fig. 16 1.
MAINTENANCE If required the paint head plunger can be removed and cleaned. This is a maintenance task and should not be required on a frequent basis. If the paint has been allowed to dry in the paint head or the spray gun has had a lot of use then removing and cleaning or replacing the plunger may restore the original spray gun performance.
TROUBLE SHOOTING Problem Cause Remedy Little or no material Nozzle clogged Clean flow Suction tube clogged Clean Material spray regulator dial setting Increase spray regulator dial turned too low (-) setting (+) Suction tube loose Insert No pressure build up in paint pot Tighten paint pot Air filter clogged Clean or replace...
SPARE PARTS Limited spare parts are available subject to availability. Please contact your local Bunnings Special Orders Desk to order the required spare parts. Most common spare parts listed below Spare Part Part No. Filter (pack 2) SPSPG300-03 Valve Spring Assy. SPSPG300-08 Nozzle Kit SPSPG300-17K...
Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice. CONTENTS 1 x Spray gun SGP-300 1 x Viscosity cup 1 x Cleaning needle 1 x Instruction manual...
PURCHASED FROM: ________________________________________________ DATE PURCHASED: ________________________________________________ 1 YEAR REPLACEMENT WARRANTY Your Ozito tool is guaranteed for a period of 12 months from the original date of purchase and is intended for DIY (Do it yourself) use only. WARNING The following actions will result in the warranty being void.
Need help?
Do you have a question about the SGP-300 and is the answer not in the manual?
Questions and answers