Related Manuals for Samsung SSA-S2000W
Summary of Contents for Samsung SSA-S2000W
-
Page 1: User Manual
SSA-S2000 Standalone RFID Access Controller user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website. www.samsungsecurity.com... -
Page 2: Safety Information
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.) . When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock. -
Page 3: Important Safety Instructions
Keep out of direct sunlight and heat radiation sources. It may cause fi re. Install it in a place with good ventilation. Avoid aiming the controller directly towards extremely bright objects such as sun. Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus. -
Page 4: Table Of Contents
contents PRODUCT INTRODUCTION INSTALLATION AND EXTERNAL CONNECTION INITIALIZATION READER MODE SETUP USER MANAGEMENT BASIC SETUP 4_ Contents Features What’s included At a Glance Cable Color Scheme Installing the rear template Cable Selection Bypass Diode Connection I/O Connection External Reader Connection Basic Operations Wiegand Output Setup Initialization... - Page 5 I/O TIME SETUP ADVANCED SETTING ADDITIONAL FEATURES OTHER INFORMATION TROUBLESHOOTING PRODUCT SPECIFICATIONS To specify the output time if the card is not authenticated To specify the Duress TTL output To specify the alarm output for an input error of the Door contact Sensor To specify the alarm operation time for AUX 1 To specify the alarm operation time for AUX 2 To specify the alarm operation time for AUX 3...
-
Page 6: Product Introduction
product introduction FEATURES This controller is best designed for a single entry door control (single door access control). It can store up to 512 cards including the Master Card that enables you to register, delete or set various user cards to your preference. -
Page 7: What's Included
WHAT’S INCLUDED Check if the following items are included in the product package. Main Unit 3.5 x 40mm Screws (x4) 3.5 x 12mm Screws (x4) 6 x 30mm Plastic Anchors (x4) Master Card (x1) Template O-rings (x5) Diodes (x2) Quick Guide (UF4004, 1N4001~4007) Cables (x4) CD Manual... -
Page 8: At A Glance
product introduction AT A GLANCE Front View System Status LED Keypad 8_ Product Introduction Indicates the operation status of the system. Use this to confi gure or release settings as appropriate, or enter a card number. -
Page 9: Cable Color Scheme
CABLE COLOR SCHEME ❖ 2-PIN Connector I/O Pins Power (+12V) DC +12V Earth-grounding GND(-) ❖ 10-PIN Connector I/O Pins Door Control Relay (NC) NC(RL1) Door Control Relay (COM) COM(RL1) Door Control Relay (NO) NO(RL1) Alarm Relay (NC) NC(RL2) Alarm Relay (COM) COM(RL2) Alarm Relay (NO) NO(RL2) -
Page 10: Installation And External Connection
installation and external connection INSTALLING THE REAR TEMPLATE 6-32 hole O-ring O-ring 1/2” hole O-ring O-ring 6-32 hole O-ring 1.52"(38.5mm) 1.52"(38.5mm) 3.03"(77mm) Once the main unit is fi xed with the rear panel, it will not be loosened. Please check if the device is operating before fi xing it. -
Page 11: Cable Selection
CABLE SELECTION RF Reader Item Power (DC12V) DC Power This Product Reader (power and data) External Reader This Product Door Contact Sensor Exit Button Sensor Input Input This Product Door Lock, Alarm Device Lock (Alarm) This Product The cables should be thick enough to allow the maximum current consumed by the reader. DC12V Power Supply Sensor Input... -
Page 12: Bypass Diode Connection
installation and external connection BYPASS DIODE CONNECTION If you connected an inductor (door locks or alarm device) to the output relay, there should occur a voltage surge while the inductor is turning on and off. If you do not connect a reverse diode to the relay, the surge voltage will cause damage to the electric circuit of the controller. - Page 13 Output Connection Connect the 10-pin and 7-pin connectors of the controller as follows: EXIT CONTACT AUX IN#1 CHIME +12V DOOR ALARM RELAY RELAY DOOR ALARM RELAY RELAY Cathode Anode 1N4004~1N4007 or equiv. DOOR LOCK SIREN - Door open (POWER FAIL SAFE) when the power is disconnected from the door lock (Door Relay) Connect the relay COM line (gray with red stripes for locking the door) to DC +12V.
-
Page 14: External Reader Connection
installation and external connection EXTERNAL READER CONNECTION 검은색- 빨간색+ DC+12V - Proximity Reader Connection Connect the DC 12V(+) of the power supply unit to the plus (+) line of the reader. Connect the GND(-) line of the power supply unit to the minus (-) line of the reader. Connect the Wiegand data input line 0 of the proximity reader to the purple line. -
Page 15: Basic Operations
initialization BASIC OPERATIONS Initial Status While the product is working normally, the orange LED indicator blinks every one second. Predefi ned Operation for a Registered Card When reading a registered card, it opens the door with the melody. Exit Button Operation If you press the Exit button, the door will be opened. -
Page 16: Wiegand Output Setup
initialization WIEGAND OUTPUT SETUP You can transfer data of the card read by SSA-S2000 in the 26-bit Wiegand output format. Enabling this function will disable the TTL output and the chime bell sound. To enable the 26-bit Wiegand output, you must manipulate the switch panel (SW1 and SW2) on the rear of the product. -
Page 17: Forced Initialization With External Line
FORCED INITIALIZATION WITH EXTERNAL LINE Turn off the product, shortcircuit between the green line and the orange line with white stripes, and turn it back on. When the initialization is completed, 3 LED indicators are blinking with a beep. Restore the connection of the two lines back to their original state. -
Page 18: Reader Mode Setup (Rf Only)
reader mode setup - You can specify the operation mode for the device. - Once a mode is specifi ed, it will not switch until you perform the initialization. - You must keep the Master Card in safe for later use as it is required for your change to the device settings. - If progression is halted for more than one minute during any of the following processes, the operation mode of the reader will return to the previous state. -
Page 19: Reader Mode Setup (Rf + P/W)
READER MODE SETUP (RF + P/W) No Master Card or Master PIN is ever registered. If you remember the Master Card or the Master PIN was registered, initialize the product and try again. When you turn on the product, all of the 3 LED indicators will fl ash with a beep. •... -
Page 20: Reader Mode Setup (Rf/Pin Combination Mode)
reader mode setup READER MODE SETUP (RF/PIN COMBINATION MODE) No Master Card or Master PIN is ever registered. If you remember the Master Card or the Master PIN was registered, initialize the product and try again. When you turn on the product, all of the 3 LED indicators will fl ash with a beep. -
Page 21: User Management
user management TO REGISTER CARDS IN RF ONLY MODE Ensure that you must have registered the Master Card and the device is specifi ed in RF ONLY mode. Present the Master Card to the device. When the mode is specifi ed, only the green LED indicator fl ashes. Press Button and Button When the device enters Standby, only the red LED indicator flashes. -
Page 22: To Register Cards In Pin Mode
user management TO REGISTER CARDS IN PIN MODE Ensure that you must have registered the Master Card and the device is specifi ed in PIN mode. Enter the Master PIN number and press When the mode is specifi ed, only the green LED indicator fl ashes. Press Button and Button When the mode is specifi... -
Page 23: To Delete A Registered Card Or Pin Number
TO DELETE A REGISTERED CARD OR PIN NUMBER Ensure that you must have registered the Master Card or the Master PIN number and the device is specifi ed in a certain mode. This is applicable in all modes. Enter the Master Card or Master PIN. When the mode is specifi... -
Page 24: Basic Setup
basic setup DURESS ALARM If you are forced to open the door under the control of a criminal such as a robber, enter the predefi ned password with the number of your registered card (or PIN), which outputs the emergency TTL signal. Present the Master Card to the device. -
Page 25: To Specify The Keypad Input Suspension Time If The Retry Count With An Unregistered Id Exceeds The Limit
TO SPECIFY THE KEYPAD INPUT SUSPENSION TIME IF THE RETRY COUNT WITH AN UNREGISTERED ID EXCEEDS THE LIMIT Present the Master Card to the device. Press Button and Button Enter the two-digit keypad input suspension time (unit: minute) and press •... -
Page 26: To Specify The Operation Time Of The Door Contact Sensor
basic setup TO SPECIFY THE OPERATION TIME OF THE DOOR CONTACT SENSOR The Door Contact sensor detects the opening of the door. If the door is forcibly opened by an unregistered user, the Door Contact Sensor will perform the predefi ned alarm operation after the set time. -
Page 27: To Specify The Alarm Output Port For The Dismantled Device
TO SPECIFY THE ALARM OUTPUT PORT FOR THE DISMANTLED DEVICE Specify the alarm type for the dismantled device. The alarm rings from the dismantlement of the device to the authentication of the Master Card or a registered card. Present the Master Card to the device. Press Button and Button Provide the alarm output port and press... -
Page 28: To Set Or Release The Quick Mode
basic setup TO SET OR RELEASE THE QUICK MODE The QUICK mode is applicable to RF ONLY mode (01) and PIN ONLY mode (03) and RF/PIN combination mode (05), which enables you to open the door by simply pressing normal business hours when the door entries and exits occur frequently.) Present the Master Card to the device. -
Page 29: To Specify The Output Time If The Card Is Authenticated
I/O time setup ❖ Output Port Setting Table You must specify the port settings using whatever combination of the followings if you want the device to operate in Secure mode or normal + Secure mode. Port Operation mode setting value Operate only in Secure mode Operate in normal mode and Secure mode Operation port setting value... - Page 30 I/O time setup TO SPECIFY THE OUTPUT TIME IF THE CARD IS NOT AUTHENTICATED You can specify the output time if an unregistered card or PIN number fails in getting authenticated. Present the Master Card to the device. Press Button twice and press Refer to the output port table on page 29 and specify a desired output mode.
- Page 31 TO SPECIFY THE ALARM OUTPUT FOR AN INPUT ERROR OF THE DOOR CONTACT SENSOR You can specify the output port and operation time if an error occurs from the Door Contact Sensor. You must have specifi ed the operation time of the Door Contact Sensor. (Refer to “To specify the operation time of the Door Contact Sensor”...
- Page 32 I/O time setup TO SPECIFY THE ALARM OPERATION TIME FOR AUX 2 Present the Master Card to the device. Press Button and Button Refer to the output port table on page 29 and specify a desired output mode. • If you want the alarm relay alone to operate in normal and Secure modes in case of an input through the auxiliary port, select the <...
-
Page 33: Contact Sensor
TO ACTIVATE OR DEACTIVATE THE DOOR RELAY BY THE DOOR CONTACT SENSOR You can set the Door Contact Sensor to control the door lock. This is to allow the Door Contact Sensor to control the door relay where the sensor keeps the door relay active from the normal opening of the door to its closing. This is useful when the door stays open with just one authentication. -
Page 34: Advanced Setting
advanced setting TO SPECIFY THE TTL OUTPUT OPERATION MODE This is to switch the TTL output from LOW (0V) to HIGH (5V) when it is activated. Present the Master Card to the device. Press Button and Button • To release the setting, repeat Step 1 above, select the <... -
Page 35: To Specify The Chime Bell Operation Time
TO SPECIFY THE CHIME BELL OPERATION TIME You can specify the chime bell operation time. Present the Master Card to the device. Press Button and Button Specify the two-digit operation time (unit: second) and press The default is set to “05” second. You can specify a time from 00 to 99 seconds. - Page 36 advanced setting TO SPECIFY THE INPUT MODE FOR AUX 2 You can specify an operation for the auxiliary port 2 when it switches from LOW (0V) to HIGH (5V). Present the Master Card to the device. Press Button and Button •...
-
Page 37: To Specify The Input Mode For The Exit Button
TO SPECIFY THE INPUT MODE FOR THE EXIT BUTTON You can specify an operation for the Exit button when it switches from LOW (0V) to HIGH (5V). Present the Master Card to the device. Press Button and Button • To release the setting, press the < ... -
Page 38: Additional Features
additional features MUTE You can mute the keypad tone or melody in normal operation. Present the Master Card to the device. Press Button and Button • To release the setting, repeat Step 1 above, select the < > buttons and press ... -
Page 39: Card User
TO CHECK THE OUTPUT SPECIFIED FOR A REGISTERED CARD USER You can check the output setting that you specifi ed in “To specify the output time if the card is authenticated”. (See page 29.) Present the Master Card to the device. Press Button and Button TO CHECK THE OUTPUT SPECIFIED FOR AN UNREGISTERED... -
Page 40: Sensor Alarm
additional features TO CHECK THE OUTPUT SPECIFIED FOR THE DOOR CONTACT SENSOR ALARM You can check the output setting that you specifi ed in “To specify the alarm output for an input error of the Door contact Sensor”. (See page 31.) Present the Master Card to the device. - Page 41 TO CHECK THE OUTPUT SPECIFIED FOR AUX 2 You can check the output setting that you specifi ed in “To specify the alarm operation time for AUX 2”. (See page 32.) Present the Master Card to the device. Press Button and Button TO CHECK THE OUTPUT SPECIFIED FOR AUX 3 You can check the output setting that you specifi...
-
Page 42: Other Information
other information INITIAL VALUES This product operates in the following initial values: For changing the settings or registering/deleting the user card, refer to the applicable section in this document. Entry permitted for a registered card - The door control relay operates for 3 seconds. - The green LED indicator fl... -
Page 43: Function Codes
FUNCTION CODES Code Number Additional user card registration (RF CARD ONLY MODE) Additional user card registration (RF CARD ONLY MODE) Additional user card and PIN registration (RF CARD + PIN MODE) Additional user card and PIN registration (RF CARD + PIN MODE) Additional PIN registration (PIN ONLY MODE) Additional PIN registration (PIN ONLY MODE) Delete a registered card or PIN number... - Page 44 other information Code Number Turn off the sound Turn off the sound Turn on the sound Turn on the sound To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit Sense if AUX 1 switches from L to H Sense if AUX 1 switches from L to H Sense if AUX 1 switches from H to L...
-
Page 45: Troubleshooting
TROUBLESHOOTING If the product does not work properly, please check the followings before contacting us. If the trouble persists, please contact the SAMSUNG Customer Service near you. Problem When I turn on the product, it does not recognize the card with just the 3 LED indicators blinking. - Page 46 troubleshooting Problem I can not register an additional user card (or PIN). 46_ Troubleshooting Action Check if the product is installed properly and works normally. - In the initial setup of the product or after it is initialized Set the operation mode and register the Master card and user cards as usual because the product is in the initial state.
- Page 47 Problem The user card (or PIN) is not deleted. I lost the Master Card and could not register or delete the card or change the settings. Action Check the operation status of the product Check if the product works properly. - If the product operates normally (and you have the Master Card or the PIN number) If you have the card to delete Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT)
- Page 48 troubleshooting Problem SSA-S2000 can recognize a presented RF card but can not recognize the RF card number using the keypad. The Exit button does not work at all. 48_ Troubleshooting Action Check if the buzzer sounds when you press a key. - If you hear the buzzer sound Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) Enter the command to enable the keypad input: 73 + ENT...
- Page 49 Problem The external reader can the RF card but the RF card data will not be transferred to SSA-S2000 or irrelevant data is transferred. The door lock does not operate at all. Action Check if the external reader is connected to SSA-S2000 properly. Check if the external reader works normally.
-
Page 50: Product Specifications
product specifi cations PRODUCT SPECIFICATIONS Item User 512 Users Power / Current DC 12V / Max.110mA Reader Port External Reder Port 1ea : 26bit Wiegand for Exit Reading Time (Card) 30ms Door Open Time 00~99 Sec. (Default 3Sec.) Input Port 5ea : Exit Button, Door Sensor, Aux#1, #2, #3 2ea : 2 Form-C Relay Output (COM, NO, NC) / DC12~18V, Rating Max.2A Output Port... - Page 51 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.