Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samsung SSA-S1000V
Summary of Contents for Samsung SSA-S1000V
- Page 1 Standalone RFID Access Controller User Manual SSA-S1000V...
- Page 2 Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
- Page 3 If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.) . When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.
- Page 4 safety information FCC Statement Caution : Any changes or modifi cations in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
-
Page 5: Table Of Contents
contents PRODUCT INTRODUCTION Feature What’s included At a Glance Cable Color Scheme Cable Selection INSTALLATION AND EXTERNAL Installation Bypass Diode Connection CONNECTION I/O Connection SYSTEM INITIALIZATION & BASIC Initializing the system by short-circuiting Basic Operations OPERATIONS To register /delete Master ID To register/delete ID card TROUBLESHOOTING TroubleShooting... -
Page 6: Feature
product introduction FEATURE This product is designed for use with one-door access control for security applications. With its compact design, you can install this product on the wall or a doorframe; Its epoxy adhesion and aluminium case guarantee shock-resistance as well as stable operation in a challenging environment. -
Page 7: What's Included
WHAT’S INCLUDED Check if the following items are included in the product package. SSA-S1000V Master Card (x1) Bezel Main Module Keytag (x5) 3.5 x 40mm Screws (x2) Diode (X 2) 3mm Hex Wrench (x1) 3.5 x 25mm Screws (x2) (UF4004, 1N4001~4007) -
Page 8: At A Glance
AT A GLANCE Front/Rear SSA-S1000V Displays the system operation status using red and green indicators. Fixing Hole Fixing hole for wall-mounting. Connection Cable Used to connect to the power or I/O cable. Tamper Switch A tamper switch to detect falling from the wall. -
Page 9: Cable Color Scheme
CABLE COLOR SCHEME Item Cable Color Signal Line Description DC+12V +12V supplied Power Black Earth-Grounding for Power Yellow AUX INPUT#1 Select a Lock Type Input Blue Door Contact Sensor Door Sensor Connection Port Green Exit Button Exit Button Connection Port Alarm Device Connection Purple Alarm Out... -
Page 10: Installation
3mm Hex Wrench - On a doorframe or the wall Drill a 1/2-inch (12.7 mm) hole onto the center of the doorframe or the wall where SSA-S1000V is installed, which makes room for the cable of the reader module. Drill a 6-32 inch hole at the 43.1mm point straight higher from the center hole and at 22.1mm straight lower, respectively. - Page 11 I/O CONNECTION Input Connection DOOR CONTACT (blue) Door Contact Sensor EXIT BUTTON Exit Button (green) SSA-S1000V DC +12V (black) DC +12V (red) DC 12V(+) POWER - To connect the power supply unit Connect the DC+12V to the red line. Connect GND to the black line.
- Page 12 Output Connection DOOR LOCK OUT (white) Door Lock ALARM OUT (purple) Alarm Device SSA-S1000V Lock Type Select (yellow) Cathode Anode 1N4004 ~ 1N4007 or equiv. DC +12V DC 12V(+) POWER - To connect the power supply unit Connect the DC+12V to the red line.
-
Page 13: Initializing The System By Short-Circuiting
Exit Button completely turned off. Yellow Lock Type In the power-off condition, all LED indicators turn green bottom up in sequence. SSA-S1000V When you hear a beep 4 times, that indicates that the initialization is completed. Black Power If you initialize the system, all of the data settings will return to the factory default. -
Page 14: To Register /Delete Master Id
& basic operations TO REGISTER /DELETE MASTER ID SSA-S1000V First turn off the product, and short-circuit two lines: purple line of Cable Alarm Out and blue line of the Door Contact Sensor. Blue When you turn the product back on, you will hear the beep twice while... -
Page 15: Troubleshooting
Master Card. The Exit button does not work at all. Check if the Exit button is connected to SSA-S1000V properly. (the Exit button should be used with a NO-type button) Check if the Exit button works normally. -
Page 16: Product Specifi Cations
PRODUCT SPECIFICATIONS Item SSA-S1000V Users 512 Users Power / Current DC 12V / Max.180mA Reading Time (Card) 30ms Door Open Time 5sec. (Fixed) Input Port 3ea: Exit Button, Door Sensor, Lock Type Select [Power fail Safe / Power Fail Secure] 2ea : TR Output / DC 12V. - Page 17 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. SAMSUNG TECHWIN EUROPE LTD. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Samsung House, 1000 Hillswood Drive, Hillswood Business Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS www.samsungcctvusa.com TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 www.samsungsecurity.com...