Avaya Scopia XT Camera Switch Quick Setup Manual

Setting Up this Device
Connect the cables as detailed in the diagram overleaf, then follow the steps below to complete
the setup of the Avaya Scopia XT Camera Switch. For details on how to use the system after
setup, see the User Guide for Avaya Scopia XT Camera Switch or the Quick Start Guide for
Avaya Scopia XT Camera Switch.
Step 1. System Installation
Place the Avaya Scopia XT Camera Switch on a horizontal
surface close to the XT Codec Unit. Maximum supplied cable
length is 40cm (0.13ft).
Step 2.
Connect one end of the HDMI cable to the OUTPUT socket on the
1.
Scopia XT Camera Switch and the other end to the vertical HDMI
connector on the XT Codec Unit.
Connect one end of the USB cable to the USB socket on the
2.
Scopia XT Camera Switch and the other end to the upper USB
connector on the XT Codec Unit.
4 3 2 1
HDMI USB
Step 3.
Check that the SYSTEM SELECT switch on the back panel of each
camera is set to 7:
SYSTEM IR SELECT
SELECT
DC IN 12V 1 2 3 IN RS-232C OUT DVI
Step 4.
Connecting the first camera
Insert the three connectors of the camera
cable (3 connectors on one side, 2 connectors
on the other side) to the sockets on the back
of the camera:
The DVI connector to the DVI socket.
1.
The 8-pin connector to the
2.
SYSTEM IR SELECT
DC IN 12V SELECT 1 2 3 IN RS-232C OUT
IN RS232C socket.
The power connector to the
3.
DC IN 12V socket.
Step 5.
Attach the two connectors on the other
end of the camera cable:
1. The HDMI connector to the HDMI socket
labeled 1 on the Scopia XT Camera Switch.
The connector for power and serial
2.
control to the horizontal socket
1
on the XT Codec Unit.
© 2000-2014 Avaya Inc. All intellectual property rights in this publication are owned by Avaya Inc. and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. Avaya Inc. retains all
rights not expressly granted.All product and company names herein may be trademarks of their registered owners. This publication is Avaya Inc. Confidential & Proprietary. Use pursuant to your signed agreement or Avaya policy. No part of this
publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Avaya Inc. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this
guide is made either by Avaya Inc. or its agents. Avaya Inc. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Avaya Inc may make improvements or changes in the
product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document.
If you are unable to locate a copy, please contact Avaya Inc and a copy will be provided to you. Unless otherwise indicated, Avaya registered trademarks are registered in the United States and other territories. All registered trademarks recognized.
For further information contact Avaya or your local distributor or reseller.
Quick Setup Guide for Avaya Scopia ® XT Camera Switch Version 8.3, March, 2014.
http://www.avaya.com
CAUTION: Make sure all units are
switched off whenever connecting
or disconnecting devices.
Step 6.
Connect the second camera as follows:
Connect the 10-meter VISCA Control cable supplied with the
1.
camera kit:
Attach one end of the VISCA control cable to the
a.
IN RS-232C connector on the second camera.
Attach the other end to the OUT RS-232C connector on the first
b.
camera.
Connect the DVI-HDMI cable as follows:
2.
Attach the DVI connector to the DVI socket on the second
a.
camera.
Attach the HDMI connector to the HDMI socket labeled 2 on the
b.
Scopia XT Camera Switch.
Connect one end of the power supply cable to the DC IN 12V
3.
connector on the camera, and the other end into one of the power
sockets on the wall.
second camera First camera
XT Camera Swirch
SYSTEM IR SELECT SYSTEM IR SELECT
DC IN 12V SELECT 1 2 3 IN RS-232C OUT DVI DC IN 12V SELECT 1 2 3 IN RS-232C OUT
2 1
Step 7.
If required, repeat the above step for a third or fourth camera.
Step 8.
Switch on the Scopia XT5000 unit,
1.
the cameras and the XT Camera
Switch.
Set Configure > General > Show
2.
Advanced Settings to Yes
Set Configure > Advanced > I/O
3.
Connections > Cameras > General >
DVI
HD Swich detect mode = Yes.
(default PIN for Advanced
configuration is 1234)
Step 9.
1. Setup each camera in the GUI
section
Configure > Advanced > I/O
Connections > Cameras as
explained
in the Installation Guide for
Avaya Scopia XT Camera Switch.
Avaya Scopia

Quick Setup Guide

DVI
Avaya Scopia XT Camera Switch
enables all the endpoints of
Avaya Scopia XT5000 series to
be connected with up to four HD
Cameras or four generic HDMI
devices (such as DVD and generic
media players). The Avaya Scopia XT
Camera Switch is fully powered and
controlled from the Avaya Scopia
XT5000 endpoint. The switch can
be controlled from XT User Interface
and Remote Control.
XT Camera Switch
®

Package Content:

•
Avaya Scopia XT Camera Switch
•
Cable USB 40cm
•
Cable HDMI M/M, 40cm