Advertisement
Screen
2 Setup input
EMU4-HM1-MB, EMU4-PX4
（
2-1.
（1） In 2-1, Push the ▲ or ▼ key , and move the cursor to the "1 Input".
[I/O]
（2） Push the
1
Input
（3） 2-2 will be displayed.
2 OP.Time
3 Output
2-2.
（1） Push the ＋ or － key , and select the input method.
[Input]
[Input]
(Non/ Contact /Pulse)
Non
Non
（2） Push the
[1]
[1]
（3） Transition to the following screen by the model and setting input method.
[Non] setting
Model：EMU4-HM1-MB → To 2-1
EMU4-PX4 only
Model：EMU4-PX4 → To 2-5
[Pulse] setting → To 2-3
[Contact] setting → To 2-4
2-3.
（1） Push the ▲
[CONV.Rate]
[CONV.Rate]
and unit.
1.000
1.000
（2） Push the
[Unit]
[Unit]
Non
Non
[1]
[1]
（3） Transition to the following screen by the model.
Model：EMU4-HM1-MB → To 2-1
EMU4-PX4 only
Model：EMU4-PX4 → To 2-5
2-4.
（1） Push the ＋ or － key, and select thereset mode.
[ResetMode]
[ResetMode]
（2） Push the
Auto
Auto
（3） Transition to the following screen by the model.
[1]
[1]
Model：EMU4-HM1-MB → To 2-1
Model：EMU4-PX4 → To 2-5
EMU4-PX4 only
2-5.
（1） Push the ＋
(Non/ Contact /Pulse)
[Input]
Non
（2） Push the
（3） Transition to the following screen by the setting input method.
[2]
[Non] setting → To 2-8
[Pulse] setting → To 2-6
[Contact] setting → To 2-7
2-6.
（1） Push the ▲ ▼ ＋ － key, and change the "CONV.Rate" value
and unit.
[CONV.Rate]
1.000
（2） Push the
[Unit]
（3） 2-8 will be displayed.
Non
[2]
2-7.
（1） Push the ＋ or － key, and select thereset mode.
[ResetMode]
（2） Push the
Auto
（3） 2-8 will be displayed.
[2]
2-8.
（1） Push the ＋
[Input]
(Non/ Contact /Pulse)
Non
（2） Push the
[3]
（3） Transition to the following screen by the setting input method.
[Non] setting → To 2-11
[Pulse] setting → To 2-9
[Contact] setting → To 2-10
2-9.
（1） Push the ▲ ▼
[CONV.Rate]
and unit.
1.000
（2） Push the
[Unit]
Non
[3]
（3） 2-11 will be displayed.
2-10.
（1） Push the ＋
[ResetMode]
（2） Push the
Auto
（3） 2-11 will be displayed.
[3]
2-11.
（1） Push the ＋
(Non/ Contact /Pulse)
[Input]
Non
（2） Push the
（3） Transition to the following screen by the setting input method.
[4]
[Non] setting → To 2-1
[Pulse] setting → To 2-12
[Contact] setting → To 2-13
2-12.
（1） Push the ▲ ▼ ＋ － key, and change the "CONV.Rate" value
[CONV.Rate]
and unit.
1.000
（2） Push the
[Unit]
Non
[4]
（3） 2-1 will be displayed.
2-13.
（1） Push the ＋ or － key, and select thereset mode.
[ResetMode]
（2） Push the
Auto
（3） 2-1 will be displayed.
[4]
Operation
）
/ Phase key.
/ Phase key.
▼ ＋
－ key, and change the "CONV.Rate" value
/ Phase key, and confirm the setting value.
/ Phase key.
or －
key , and select the input method.
/ Phase key.
/ Phase key, and confirm the setting value.
/ Phase key.
or
－ key , and select the input method.
/ Phase key.
＋ － key, and change the "CONV.Rate" value
/ Phase key, and confirm the setting value.
or － key, and select thereset mode.
/ Phase key.
or － key , and select the input method.
/ Phase key.
/ Phase key, and confirm the setting value.
/ Phase key.
<EMU4-HM1-MB>
[Input]：Non⇔Contact⇔Pulse⇔
<EMU4-PX4>
[Input]：Pulse⇔Contact⇔Non⇔
[CONV.Rate]：0.001～10000（1.000）
[Unit]：Non⇔Ｗｈ⇔ｋＷｈ⇔ＭＷｈ⇔Ｊ⇔ｍ
[ResetMode]：Auto⇔Hold⇔
Auto...Contact input state is reset automaticaly when
Hold...Contact input state is hold until contact input
- 9 -
Note
2
⇔ｍ
ｋＬ⇔sec⇔min⇔hour⇔個⇔台⇔ｇ⇔ｋｇ⇔ｔ⇔
￥⇔＄⇔
contact input is less.
released even thought contact input is less.
(For information about how to release of the
contact input, please refer to the instruction
manual (Detailed edition))
3
⇔Ｌ⇔
Advertisement
