Advertisement
Screen
12-17.
（1） Push the ▲
[Scaling]
limit, and unit.
Upp.: 04095
（2） Push the
Low.: 00000
Unit:Non
[4]
（3） 12-1 will be displayed.
13 Setup the Number Limit
13-1.
（1） In 13-1, push the ▲ or ▼ key, and move the cursor to the
[Measure]
"12 Num.Limit".
10DIF.CONV.
（2） Push the
11AD CONV.
12Num.Limit
（3） 13.1-1 will be displayed.
13.1 Setup the Limit A, Limit B, Limit C, and Limit D
13.1-1.
（1） In 13.1-1, push the ▲ or ▼ key, and move the cursor to the
[Num.Limit]
"1 Limit A".
1
Limit A
（2） Push the
2 Limit B
3 Limit C
（3） 13.1-2 will be displayed.
13.1-2.
（1） Push the
[Limit A]
（2） Push the
-32767
（3） 13.1-3 will be displayed.
[1]
13.1-3.
（1） Push the
[Limit A]
（2） Push the
-32767
（3） 13.1-4 will be displayed.
[2]
13.1-4
（1） Push the
[Limit A]
（2） Push the
-32767
（3） 13.1-5 will be displayed.
[3]
13.1-5
（1） Push the
[Limit A]
（2） Push the
-32767
（3） 13.1-1 will be displayed.
[4]
13.2 Setup the multiplying factor
13.2-1.
（1） In 13.2-1, push the ▲ or ▼ key, and move the cursor to the
[Num.Limit]
"5 Factor".
3 Limit C
（2） Push the
4 Limit D
5
Factor
（3） 13.2-2 will be displayed.
13.2-2.
（1） Push the
[Factor]
（2） Push the
x1
（3） 13.2-3 will be displayed.
[1]
13.2-3.
（1） Push the
[Factor]
（2） Push the
x1
（3） 13.2-4 will be displayed.
[2]
13.2-4
（1） Push the
[Factor]
（2） Push the
x1
（3） 13.2-5 will be displayed.
[3]
13.2-5
（1） Push the
[Factor]
（2） Push the
x1
（3） 13.2-1 will be displayed.
[4]
14 Save the settings
14-1.
（1） After setting all of the items, and push the Setup key.
Quit Setup
（2） 14-1 will be displayed.
1
Save
（3） When save the settings, push the ▲ or ▼ key, move the cursor to
2 Not Save
3 Cancel
the "1 Save", and push the
（4） After completing the settings saving, 14-2 will be displayed.
14-2.
Push the
Completed
（5） Return to the operation mode.
OK
*Setting for condition of the measurement mode can only configure in the display unit is set to master.（Setting for condition of the measurement mode can not configure in
the display unit is set to slave.）
*If you change a settings, please push the
*The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
*If you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
*Same voltage system is same setting in wire system, primary voltage, 2 circuits Measuring existence, Simple measurement.
7.2.2 Input/Output setup－the settings for the external Input/Output. EMU4-LG1-MB is not set.
Screen
1 Transit to the Setup mode
1-1.
（1） Push the Setup
[Setup]
（2） 1-1 will be displayed.
1 Measure
（1） Push the ▲ or ▼ key, and move the cursor to the "2 I/O".
2
I/O
3 COM.
Push the
（2） 2-1 will be displayed.
Operation
▼ ＋
－ key, and change the scalling upper limit, lower
/ Phase key, and confirm the setting value.
EMU4-AX4 only
（
）
/ Phase key.
EMU4-AX4 only
（
/ Phase key.
▲
▼
－ key, and change the set value.
＋
/ Phase key.
▲
▼
－ key, and change the set value.
＋
/ Phase key.
▲
▼
－ key, and change the set value.
＋
/ Phase key.
▲
▼
－ key, and change the set value.
＋
/ Phase key.
EMU4-AX4 only
（
）
/ Phase key.
or － key, and select the multiplying factor displayed.
＋
/ Phase key.
＋ or
－ key, and select the multiplying factor displayed.
/ Phase key.
＋ or － key, and select the multiplying factor displayed.
/ Phase key.
＋ or － key, and select the multiplying factor displayed.
/ Phase key.
/ Phase key.
/Phase key.
/ Phase key and be sure to determine changes. If without determine, the changes will be discarded.
Operation
key in operation mode.
/ Phase key.
[Upp]：-32767～32767（4095）
[Low]：-32767～32767（0）
[Unit]：Non⇔A⇔mA⇔kA⇔V⇔kV⇔W⇔kW⇔MW⇔Hz⇔N⇔
Num.Limit...Set any limint .
*If the scaling value over the limit, Number Limit
）
Limit B, Limit C, and Limit D is done in the same way
as the setting of Limit A.
Limit...Set any scalling value.
[Limit A]：Scaling Low～Scaling Upp
*If scaling setting value is set "Scaling Low > Scaling
Upp", default setting is Scaling Upp.
[Factor]：x1⇔x10⇔x100⇔x1000⇔
Factor...Set up the multiplying factor displayed of
1 Save
2 Not Save → Discard the changes and
3 Cancel
- 8 -
Note
kN⇔Pa⇔kPa⇔MPa⇔C⇔deg⇔%⇔
countup.
You can configure the four different limits for
limit A, limit B, limit C, and limit D.
Number Limit.
→ Save settings and return to
the operation mode.
return to the operation mode.
→Continue the setup.
Note
Advertisement
