Advertisement
Screen
5 Save the settings
5-1.
（1） After setting all of the items, push the Setup key.
Quit Setup
（2） 5-1 will be displayed.
1
Save
（3） When save the settings, push the ▲ or ▼ key, move the cursor to
2 Not Save
3 Cancel
the "1 Save", and Push the
（4） After completing the settings saving, "Completed"message will be
displayed. Push the
（5） Return to the operation mode.
*Full load is calculated by following formula. (Full load)＝(Primary voltage) x (Primary current) x (Coefficient) / 1000[kW]
*If you change a settings, please push the
*
The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
*
If
you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
7.2.3 Communication setup－the settings for the MODBUS communication （EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB only）
Screen
1 Transition to the setup mode
1-1.
（1） Push the Setup
[Setup]
（2） 1-1 will be displayed.
1 Measure
（1） Confirm that the cursor focuses the "3 COM.", push the
2 I/O
3
COM.
（2） 2-1 will be displayed.
2
MODBUS address
Setup
2-1.
（1） In 2-1, Push the ▲ or ▼ key, and move the cursor to the "1 Address".
[COM.]
（2） Push the
1
Address
（3） 2-2 will be displayed.
2 Baut rate
3 Parity
2-2.
（1） Push the ▲ ▼ ＋ － key, and change the address.
[Address]
（2） Push the
001
（3） 2-1 will be displayed.
3 Setup the baut rate
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
（
3-1.
（1） In 3-1, Push the ▲ or ▼ key, and move the cursor to the "2 Baut rate".
[COM.]
（2） Push the
1 Address
（3） 3-2 will be displayed.
2
Baut rate
3 Parity
3-2.
（1） Push the ＋ or － key, and select the baut rate.
[Baut rate]
（2） Push the
19200bps
（3） 3-1 will be displayed.
4 Setup the parity
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
（
4-1.
（1） In 4-1, Push the ▲ or ▼ key, and move the cursor to the "3 Parity".
[COM.]
（2） Push the
1 Address
（3） 4-2 will be displayed.
2 Baut rate
3
Parity
4-2.
（1） Push the ＋ or － key, and select the parity.
[Parity]
（2） Push the
Even
（3） 4-1 will be displayed.
5 Setup the stop bit
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
（
5-1.
（1） In 5-1, Push the ▲ or ▼ key, and move the cursor to the "4 Stop bit".
[COM.]
（2） Push the
2 Baut rate
（3） 5-2 will be displayed.
3 Parity
4
Stop bit
5-2.
（1） Push the ＋
[Stop bit]
（2） Push the
1
（3） 5-1 will be displayed.
6 Save the settings
6-1.
（1） After setting all of the items, push the Setup key.
Quit Setup
（2） 6-1 will be displayed.
1
Save
（3） When save the settings, push the ▲ or ▼ key, move the cursor to
2 Not Save
3 Cancel
the "1 Save", and Push the
（4） After completing the settings saving, "Completed" message will be
displayed. Push the
（5） Return to the operation mode, and it will be displayed electric energy screen.
*If you change a settings, please push the
*The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
*If you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
Operation
/ Phase key.
/Phase key.
*1: In case 3P4W, apply the not phase voltage but line voltage as primary voltage.
*2: Coefficient is varies according to the phase wire system. 1P2W →1, 3P3W/3P4W →1.73
/ Phase key and be sure to determine changes. If without determine, the changes will be discarded.
Operation
key in operation mode.
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
（
/ Phase key.
/ Phase key,and confirm the setting value.
/ Phase key.
/ Phase key.
/ Phase key.
/ Phase key.
/ Phase key.
or － key, and select the stop bit.
/ Phase key.
/ Phase key.
/Phase key.
/ Phase key and be sure to determine changes. If without determine, the changes will be discarded.
1 Save
2 Not Save → Discard the changes and
3 Cancel
/ Phase key.
）
[Address]：001～255
）
[Baut rate]：2400⇔4800⇔9600⇔19200⇔38400⇔
）
[Parity]：Non⇔Even⇔Odd⇔
）
[Stop bit]：1⇔2⇔
1 Save
2 Not Save → Discard the changes and
3 Cancel
- 11 -
Note
→ Save settings and return to
the operation mode.
return to the operation mode.
→Continue the setup.
Note
→ Save settings and return to
the operation mode.
return to the operation mode.
→Continue the setup.
Advertisement
