Ethernet Communications; Cables And Drivers - red lion GRAPHITE G07C Manual

c
ommunicating
CONFIGURING GRAPHITE
The Graphite is configured using Crimson
a free download from Red Lion's website. Updates to Crimson for new features
and drivers are posted on the website as they become available. By configuring
the Graphite using the latest version of Crimson, you are assured that your unit
has the most up to date feature set. Crimson
through the RS232 PGM port, USB port, or SD card.
The USB port is connected using a standard USB cable with a Type B
connector. The driver needed to use the USB port will be installed with Crimson.
The RS232 PGM port uses a programming cable made by Red Lion to connect
to the DB9 COM port of your computer. If you choose to make your own cable,
use the "Port Pin Out Diagram" that corresponds to your specific model for
wiring information.
The SD card can be used to program a Graphite by placing a configuration file
and firmware on the SD card. The card is then inserted into the target Graphite
and powered. Refer to the Crimson literature for more information on the proper
names and locations of the files.
USB, DATA TRANSFERS FROM THE SD
CARD
WARNING - DO NOT CONNECT OR DISCONNECT CABLES
WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND
DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT
CONNECTION.
In order to transfer data from the SD card via the USB port, a driver must be
installed on your computer. This driver is installed with Crimson and is located
in the folder C:\Program Files\Red Lion Controls\Crimson 3.0\Device\ after
Crimson is installed. This may have already been accomplished if your Graphite
was configured using the USB port.
Once the driver is installed, connect the Graphite to your PC with a USB
cable, and follow "Mounting the SD" instructions in the Crimson 3 user manual.
USB HOST LEDS
COLOR STATUS
OFF Not operational
RED Error
GREEN Normal operation
INSERTION/REMOVAL OF THE SD CARD
Insert the SD card into the slot provided with the card oriented as shown. The
card is inserted properly when the end of the card is flush with the Graphite
case. To remove the SD card, push in slightly on the card.

CABLES AND DRIVERS

Red Lion has a wide range of cables and drivers for use with many different
communication types. A list of these drivers and cables along with pin outs is
available from Red Lion's website. New cables and drivers are added on a
regular basis. If making your own cable, refer to the "Port Pin Outs" that
corresponds to your specific model for wiring information.
W
ith the
®
software. Crimson is available as
®
software can configure the Graphite
g
raphite

ETHERNET COMMUNICATIONS

Ethernet communications can be established at either 10 BASE-T or 100
BASE-TX. The Graphite unit's RJ45 jack is wired as a NIC (Network Interface
Card). For example, when wiring to a hub or switch use a straight-through cable,
but when connecting to another NIC use a crossover cable.
The Ethernet connector contains two LEDs. A yellow LED in the upper right,
and a green LED in the upper left. The LEDs represent the following statuses:
LED COLOR
YELLOW solid
YELLOW flashing
GREEN (OFF)
GREEN (ON)
On the rear of each unit is a unique 12-digit MAC address and a block for
marking the unit with an IP address. Refer to the Crimson manual and Red
Lion's website for additional information on Ethernet communications.
RS232 PORTS
The Graphite has two RS232
ports. There is the PGM port and the
COMMS port. Although only one of
these ports can be used for
programming, both ports can be used
for communications with a PLC.
The RS232 ports can be used for
either master or slave protocols with
any Graphite configuration.
RS422/485 COMMS PORT
The Graphite has one RS422/485 port. This port can be configured to act as
either RS422 or RS485.
RS422/485 4-WIRE
CONNECTIONS
5V
130K
7
1
TX
8
130K 2
5
5V
130K
4
RX
3
130K
6
Note: All Red Lion devices connect A to A and B to B. Refer to www.redlion.net
for additional information.
7 7
DESCRIPTION
Link established.
Data being transferred.
10 BASE-T Communications
100 BASE-TX Communications
Graphite RS232 to a PC
Gxx: RJ12 Name PC: DB9 Name
4 COMM 1
5 Tx 2
2 Rx 3
N/C 4
3 COMM 5
N/C 6
1 CTS 7
6 RTS 8
N/C 9
RS485 2-WIRE
CONNECTIONS
5V
130K
TxB
TX/RX
TxA
130K
TxEN (OC)
RxB
RxA
COMM
DCD
Rx
Tx
DTR
GND
DSR
RTS
CTS
RI
7
TxB
1
8
TxA
2
5 TxEN (OC)
6 COMM